Creative Automation System
Creative Automation System
Basant Vihar, Bhilwara, Rajasthan
GST No. 08AAKPO4851B1ZQ
TrustSEAL Verified
Call 08043046585 94% Response Rate
SEND EMAIL

Controllers Timers And Counters

Manufacturer of a wide range of products which include bl77 counters timer, bl99 counters timer, ai 5441 digital temperature controller, ai 5841 digital temperature controller, ai 5941 digital temperature controller and ai 5942 digital temperature controller.

BL77 Counters Timer

BL77 Counters Timer
  • BL77 Counters Timer
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberBL - 77
Size72 X 72 Inch
Operating Temp.0-55 Deg C
Accuracy0.05 % Full Scale
Memory RetentionUp to 10 Year
Sensor Supply12 V DC (+-10%) @ 30 mA
Humidity95 % RN
BrandI Therm
Supply90 to 270 V AC

Safety Instruction:
  • This controller is meant for Batch & Length counter applications. It is important to read the manual prior to installing or commissioning of controller. All safety related instruction appearing in this manual must be followed to ensure safety of the operating personnel as well as the instrument.
General:
  • The controller must be configured correctly for intendedoperation. Incorrect configuration could result in damage to theequipment or the process under control or it may lead personnelinjury.
  • The controller is generally part of control panel and in such acase the terminals should not remain accessible to the user afterinstallation.

Mechanical:

  • The Controller in its installed state must not come in close proximity to any corrosive/combustible gases, caustic vapors, oils, steam or any other process by products.
  • The Controller in its installed state should not be exposed to carbon dust, salt air, direct sunlight or radiant heat.
  • Ambient temperature and relative humidity surrounding the controller must not exceed the maximum specified limit for proper operation of the controller.
  • The controller in its installed state must be protected against excessive electrostatic or electromagnetic interferences.
  • Ventilation holes provided on the chassis of the instrument are meant for thermal dissipation hence should not be obstructed in the panel.

Electrical:
  • The controller must be wired as per wiring diagram & it must comply with local electrical regulation.
  • Care must be taken not to connect AC supplies to low voltage sensor input.
  • Circuit breaker or mains s/w with fuse (275V/1A) must be installed between power supply and supply terminals to protect the controller from any possible damage due to high voltage surges of extended duration.
  • Circuit breaker and appropriate fuses must be used for driving high voltage loads to protect the controller from any possible damage due to short circuit on loads.
  • To minimize pickup of electrical noise, the wiring for low voltage DC and sensor input must be routed away from high current power cables. Where it is impractical to do this, use shielded ground at both ends.
  • The controller should not be wired to a 3-Phase supply with unearthed star connection. Under fault condition such supply could rise above 264 VAC which will damage the controller.
  • The Electrical noise generated by switching inductive loads might create momentary Fluctuation in display, alarm latch up, data loss or permanent damage to the instrument. To reduce this use snubber circuit across the load.
Request
Callback
Yes! I am Interested

BL99 Counters Timer

BL99 Counters Timer
  • BL99 Counters Timer
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberBL99
Size96 X 96 cm
Operating Temp.0-55 Deg C
Accuracy0.05 % Full Scale
Memory RetentionUp to 10 Year
Sensor Supply12 V DC (+-10%) @ 30 mA
Humidity95% RN (Non Condensing)
BrandI Therm
Supply90 to 270 V AC
MountingPanel

Safety Instruction:
  • This controller is meant for Batch & Length counter applications. It is important to read the manual prior to installing or commissioning of controller. All safety related instruction appearing in this manual must be followed to ensure safety of the operating personnel as well as the instrument.
General:
  • The controller must be configured correctly for intendedoperation. Incorrect configuration could result in damage to theequipment or the process under control or it may lead personnelinjury.
  • The controller is generally part of control panel and in such acase the terminals should not remain accessible to the user afterinstallation.

Mechanical:
  • The Controller in its installed state must not come in close proximity to any corrosive/combustible gases, caustic vapors, oils, steam or any other process by products.
  • The Controller in its installed state should not be exposed to carbon dust, salt air, direct sunlight or radiant heat.
  • Ambient temperature and relative humidity surrounding the controller must not exceed the maximum specified limit for proper operation of the controller.
  • The controller in its installed state must be protected against excessive electrostatic or electromagnetic interferences.
  • Ventilation holes provided on the chassis of the instrument are meant for thermal dissipation hence should not be obstructed in the panel.

Electrical:
  • The controller must be wired as per wiring diagram & it must comply with local electrical regulation.
  • Care must be taken not to connect AC supplies to low voltage sensor input.
  • Circuit breaker or mains s/w with fuse (275V/1A) must be installed between power supply and supply terminals to protect the controller from any possible damage due to high voltage surges of extended duration.
  • Circuit breaker and appropriate fuses must be used for driving high voltage loads to protect the controller from any possible damage due to short circuit on loads.
  • To minimize pickup of electrical noise, the wiring for low voltage DC and sensor input must be routed away from high current power cables. Where it is impractical to do this, use shielded ground at both ends.
  • The controller should not be wired to a 3-Phase supply with unearthed star connection. Under fault condition such supply could rise above 264 VAC which will damage the controller.
  • The Electrical noise generated by switching inductive loads might create momentary Fluctuation in display, alarm latch up, data loss or permanent damage to the instrument. To reduce this use snubber circuit across the load.
Request
Callback
Yes! I am Interested

AI 5441 Digital Temperature Controller

AI 5441 Digital Temperature Controller
  • AI 5441 Digital Temperature Controller
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberAI - 5441
BrandI Therm
Size48*48 mm
Sampling Time125 msec
Resolution1 Deg C
Drive Capacity12V @ 30 mA

Safety Instruction:
  • This controller is meant for temperature control applications. It is important to read the manual prior to installing or commissioning of controller. All safety related instructions appearing in this manual must be followed to ensure safety of the operating personnel as well as the instrument.

General:
  • The controller must be configured correctly for intended operation. Incorrect configuration could result in damage to the equipment or the process under control or it may lead to personnel injury. 
  • The controller is generally part of control panel and in such a case the terminals should not remain accessible to the user after installation. 

Mechanical

  • The Controller in its installed state must not come in close proximity to any corrosive/combustible gases, caustic vapors, oils, steam or any other process byproducts. 
  • The Controller in its installed state should not be exposed to carbon dust, salt air, direct sunlight or radiant heat 
  • Ambient temperature and relative humidity surrounding the controller must not exceed the maximum specified limit for proper operation of the controller. 
  • The controller in its installed state must be protected against excessive electrostatic or electromagnetic interferences. Ventilation slits provided on the chassis of the instrument are meant for thermal dissipation hence should not be obstructed in the panel.

Electrical:
  • The controller must be wired as per wiring diagram & it must comply with local electrical regulation. 
  • Care must be taken not to connect AC supplies to low voltage sensor input. 
  • Circuit breaker or mains s/w with fuse (275V/1A) must be installed between power supply and supply terminals to protect the controller from any possible damage due to high voltage surges of extended duration. 
  • Circuit breaker and appropriate fuses must be used for driving high voltage loads to protect the controller from any possible damage due to short circuit on loads. 
  • To minimize pickup of electrical noise, the wiring for low voltage DC and sensor input must be routed away from high current power cables. Where it is impractical to do so, use shielded ground at both ends. 
  • The controller should not be wired to a 3-Phase supply with unearthed star connection. Under fault condition such supply could rise above 264 VAC which will damage the controller. 
  • The Electrical noise generated by switching inductive loads might create momentary Fluctuation in display, alarm latch up, data loss or permanent damage to the instrument. To reduce this use snubber circuit across the load. 
  • It is essential to install a over Temp. Protection device to avoid any failure of heating system. Apart from spoiling the product, this could damage the process being controlled.
Request
Callback
Yes! I am Interested

AI 5841 Digital Temperature Controller

AI 5841 Digital Temperature Controller
  • AI 5841 Digital Temperature Controller
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberAI 5841
BrandI Therm
Size48*96 mm
Humidity5~90% Rh
Sampling Time125 msec
Display Height0.56 Inch
Resolution1 Deg C
Digital Filter1 to 10 Sec
Operating Range0 ~50 Deg C
Supply Voltage90~270 VAC
Frequency50-60 Hz

Safety Instruction:
  • This controller is meant for temperature control applications. It is important to read the manual prior to installing or commissioning of controller. All safety related instructions appearing in this manual must be followed to ensure safety of the operating personnel as well as the instrument.

General:
  • The controller must be configured correctly for intended operation. Incorrect configuration could result in damage to the equipment or the process under control or it may lead to personnel injury. 
  • The controller is generally part of control panel and in such a case the terminals should not remain accessible to the user after installation. 

Mechanical

  • The Controller in its installed state must not come in close proximity to any corrosive/combustible gases, caustic vapors, oils, steam or any other process byproducts. 
  • The Controller in its installed state should not be exposed to carbon dust, salt air, direct sunlight or radiant heat 
  • Ambient temperature and relative humidity surrounding the controller must not exceed the maximum specified limit for proper operation of the controller. 
  • The controller in its installed state must be protected against excessive electrostatic or electromagnetic interferences. Ventilation slits provided on the chassis of the instrument are meant for thermal dissipation hence should not be obstructed in the panel.

Electrical:
  • The controller must be wired as per wiring diagram & it must comply with local electrical regulation. 
  • Care must be taken not to connect AC supplies to low voltage sensor input. 
  • Circuit breaker or mains s/w with fuse (275V/1A) must be installed between power supply and supply terminals to protect the controller from any possible damage due to high voltage surges of extended duration. 
  • Circuit breaker and appropriate fuses must be used for driving high voltage loads to protect the controller from any possible damage due to short circuit on loads. 
  • To minimize pickup of electrical noise, the wiring for low voltage DC and sensor input must be routed away from high current power cables. Where it is impractical to do so, use shielded ground at both ends. 
  • The controller should not be wired to a 3-Phase supply with unearthed star connection. Under fault condition such supply could rise above 264 VAC which will damage the controller. 
  • The Electrical noise generated by switching inductive loads might create momentary Fluctuation in display, alarm latch up, data loss or permanent damage to the instrument. To reduce this use snubber circuit across the load. 
  • It is essential to install a over Temp. Protection device to avoid any failure of heating system. Apart from spoiling the product, this could damage the process being controlled.
Request
Callback
Yes! I am Interested

AI 5941 Digital Temperature Controller

AI 5941 Digital Temperature Controller
  • AI 5941 Digital Temperature Controller
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberAI 5941
BrandI Therm
Size96*96 mm
Humidity5~90% Rh
Sampling Time125 msec
Display Height0.56 Inch
Resolution1 Deg C
Digital Filter1 to 10 Sec
Operating Range0 ~50 Deg C
Supply Voltage90~270 VAC
Frequency50-60 Hz

Safety Instruction:
  • This controller is meant for temperature control applications. It is important to read the manual prior to installing or commissioning of controller. All safety related instructions appearing in this manual must be followed to ensure safety of the operating personnel as well as the instrument.

General:
  • The controller must be configured correctly for intended operation. Incorrect configuration could result in damage to the equipment or the process under control or it may lead to personnel injury. 
  • The controller is generally part of control panel and in such a case the terminals should not remain accessible to the user after installation. 

Mechanical

  • The Controller in its installed state must not come in close proximity to any corrosive/combustible gases, caustic vapors, oils, steam or any other process byproducts. 
  • The Controller in its installed state should not be exposed to carbon dust, salt air, direct sunlight or radiant heat 
  • Ambient temperature and relative humidity surrounding the controller must not exceed the maximum specified limit for proper operation of the controller. 
  • The controller in its installed state must be protected against excessive electrostatic or electromagnetic interferences. Ventilation slits provided on the chassis of the instrument are meant for thermal dissipation hence should not be obstructed in the panel.

Electrical:
  • The controller must be wired as per wiring diagram & it must comply with local electrical regulation. 
  • Care must be taken not to connect AC supplies to low voltage sensor input. 
  • Circuit breaker or mains s/w with fuse (275V/1A) must be installed between power supply and supply terminals to protect the controller from any possible damage due to high voltage surges of extended duration. 
  • Circuit breaker and appropriate fuses must be used for driving high voltage loads to protect the controller from any possible damage due to short circuit on loads. 
  • To minimize pickup of electrical noise, the wiring for low voltage DC and sensor input must be routed away from high current power cables. Where it is impractical to do so, use shielded ground at both ends. 
  • The controller should not be wired to a 3-Phase supply with unearthed star connection. Under fault condition such supply could rise above 264 VAC which will damage the controller. 
  • The Electrical noise generated by switching inductive loads might create momentary Fluctuation in display, alarm latch up, data loss or permanent damage to the instrument. To reduce this use snubber circuit across the load. 
  • It is essential to install a over Temp. Protection device to avoid any failure of heating system. Apart from spoiling the product, this could damage the process being controlled.
Request
Callback
Yes! I am Interested

AI 5942 Digital Temperature Controller

AI 5942 Digital Temperature Controller
  • AI 5942 Digital Temperature Controller
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberAI 5942
BrandI Therm
Sampling Time125 msec
Display Height0.56 Inch
Resolution1 Deg C
Digital Filter1 to 10 Sec
Drive Capacity12V @ 30mA
Operating Range0 ~50 Deg C
Storage Humidity95% Rh (Non-condensing)

Safety Instruction:
  • This controller is meant for temperature control applications. It is important to read the manual prior to installing or commissioning of controller. All safety related instructions appearing in this manual must be followed to ensure safety of the operating personnel as well as the instrument.

General:
  • The controller must be configured correctly for intended operation. Incorrect configuration could result in damage to the equipment or the process under control or it may lead to personnel injury. 
  • The controller is generally part of control panel and in such a case the terminals should not remain accessible to the user after installation. 

Mechanical

  • The Controller in its installed state must not come in close proximity to any corrosive/combustible gases, caustic vapors, oils, steam or any other process byproducts. 
  • The Controller in its installed state should not be exposed to carbon dust, salt air, direct sunlight or radiant heat 
  • Ambient temperature and relative humidity surrounding the controller must not exceed the maximum specified limit for proper operation of the controller. 
  • The controller in its installed state must be protected against excessive electrostatic or electromagnetic interferences. Ventilation slits provided on the chassis of the instrument are meant for thermal dissipation hence should not be obstructed in the panel.

Electrical:
  • The controller must be wired as per wiring diagram & it must comply with local electrical regulation. 
  • Care must be taken not to connect AC supplies to low voltage sensor input. 
  • Circuit breaker or mains s/w with fuse (275V/1A) must be installed between power supply and supply terminals to protect the controller from any possible damage due to high voltage surges of extended duration. 
  • Circuit breaker and appropriate fuses must be used for driving high voltage loads to protect the controller from any possible damage due to short circuit on loads. 
  • To minimize pickup of electrical noise, the wiring for low voltage DC and sensor input must be routed away from high current power cables. Where it is impractical to do so, use shielded ground at both ends. 
  • The controller should not be wired to a 3-Phase supply with unearthed star connection. Under fault condition such supply could rise above 264 VAC which will damage the controller. 
  • The Electrical noise generated by switching inductive loads might create momentary Fluctuation in display, alarm latch up, data loss or permanent damage to the instrument. To reduce this use snubber circuit across the load. 
  • It is essential to install a over Temp. Protection device to avoid any failure of heating system. Apart from spoiling the product, this could damage the process being controlled.
Request
Callback
Yes! I am Interested

AI 5981 Digital Temperature Controller

AI 5981 Digital Temperature Controller
  • AI 5981 Digital Temperature Controller
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberAI 5981
BrandI Therm
Sampling Time125 msec
Display Height0.56 Inch
Resolution1 Deg C
Digital Filter1 to 10 Sec
Drive Capacity12V @ 30mA
Operating Range0 ~50 Deg C
Storage Humidity95% Rh (Non-condensing)
Supply Voltage90~270 VAC
Frequency50-60 Hz

Safety Instruction:
  • This controller is meant for temperature control applications. It is important to read the manual prior to installing or commissioning of controller. All safety related instructions appearing in this manual must be followed to ensure safety of the operating personnel as well as the instrument.

General:
  • The controller must be configured correctly for intended operation. Incorrect configuration could result in damage to the equipment or the process under control or it may lead to personnel injury. 
  • The controller is generally part of control panel and in such a case the terminals should not remain accessible to the user after installation. 

Mechanical

  • The Controller in its installed state must not come in close proximity to any corrosive/combustible gases, caustic vapors, oils, steam or any other process byproducts. 
  • The Controller in its installed state should not be exposed to carbon dust, salt air, direct sunlight or radiant heat 
  • Ambient temperature and relative humidity surrounding the controller must not exceed the maximum specified limit for proper operation of the controller. 
  • The controller in its installed state must be protected against excessive electrostatic or electromagnetic interferences. Ventilation slits provided on the chassis of the instrument are meant for thermal dissipation hence should not be obstructed in the panel.

Electrical:
  • The controller must be wired as per wiring diagram & it must comply with local electrical regulation. 
  • Care must be taken not to connect AC supplies to low voltage sensor input. 
  • Circuit breaker or mains s/w with fuse (275V/1A) must be installed between power supply and supply terminals to protect the controller from any possible damage due to high voltage surges of extended duration. 
  • Circuit breaker and appropriate fuses must be used for driving high voltage loads to protect the controller from any possible damage due to short circuit on loads. 
  • To minimize pickup of electrical noise, the wiring for low voltage DC and sensor input must be routed away from high current power cables. Where it is impractical to do so, use shielded ground at both ends. 
  • The controller should not be wired to a 3-Phase supply with unearthed star connection. Under fault condition such supply could rise above 264 VAC which will damage the controller. 
  • The Electrical noise generated by switching inductive loads might create momentary Fluctuation in display, alarm latch up, data loss or permanent damage to the instrument. To reduce this use snubber circuit across the load. 
  • It is essential to install a over Temp. Protection device to avoid any failure of heating system. Apart from spoiling the product, this could damage the process being controlled.
Request
Callback
Yes! I am Interested

AI 5982 Digital Temperature Controller

AI 5982 Digital Temperature Controller
  • AI 5982 Digital Temperature Controller
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberAI 5982
BrandI Therm
Sampling Time125 msec
Display Height0.56 Inch
Resolution1 Deg C
Digital Filter1 to 10 Sec
Drive Capacity12V @ 30mA.
Operating Range0 ~50 Deg C
Storage Humidity95% Rh
Supply Voltage90~270 VAC
Frequency50-60 Hz

Safety Instruction:
  • This controller is meant for temperature control applications. It is important to read the manual prior to installing or commissioning of controller. All safety related instructions appearing in this manual must be followed to ensure safety of the operating personnel as well as the instrument.

General:
  • The controller must be configured correctly for intended operation. Incorrect configuration could result in damage to the equipment or the process under control or it may lead to personnel injury. 
  • The controller is generally part of control panel and in such a case the terminals should not remain accessible to the user after installation. 

Mechanical

  • The Controller in its installed state must not come in close proximity to any corrosive/combustible gases, caustic vapors, oils, steam or any other process byproducts. 
  • The Controller in its installed state should not be exposed to carbon dust, salt air, direct sunlight or radiant heat 
  • Ambient temperature and relative humidity surrounding the controller must not exceed the maximum specified limit for proper operation of the controller. 
  • The controller in its installed state must be protected against excessive electrostatic or electromagnetic interferences. Ventilation slits provided on the chassis of the instrument are meant for thermal dissipation hence should not be obstructed in the panel.

Electrical:
  • The controller must be wired as per wiring diagram & it must comply with local electrical regulation. 
  • Care must be taken not to connect AC supplies to low voltage sensor input. 
  • Circuit breaker or mains s/w with fuse (275V/1A) must be installed between power supply and supply terminals to protect the controller from any possible damage due to high voltage surges of extended duration. 
  • Circuit breaker and appropriate fuses must be used for driving high voltage loads to protect the controller from any possible damage due to short circuit on loads. 
  • To minimize pickup of electrical noise, the wiring for low voltage DC and sensor input must be routed away from high current power cables. Where it is impractical to do so, use shielded ground at both ends. 
  • The controller should not be wired to a 3-Phase supply with unearthed star connection. Under fault condition such supply could rise above 264 VAC which will damage the controller. 
  • The Electrical noise generated by switching inductive loads might create momentary Fluctuation in display, alarm latch up, data loss or permanent damage to the instrument. To reduce this use snubber circuit across the load. 
  • It is essential to install a over Temp. Protection device to avoid any failure of heating system. Apart from spoiling the product, this could damage the process being controlled.
Request
Callback
Yes! I am Interested

AI 5741 Digital Temperature Controller

AI 5741 Digital Temperature Controller
  • AI 5741 Digital Temperature Controller
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberAI 5741
BrandI Therm
Sampling Time125 msec
Display Height0.56 Inch
Resolution1 Deg C
Digital Filter1 to 10 Sec
Operating Range0 ~50 Deg C
Storage Humidity95% Rh (Non-condensing)
Supply Voltage90~270 VAC
Frequency50-60 Hz
Power Consumption4 W

Safety Instruction:
  • This controller is meant for temperature control applications. It is important to read the manual prior to installing or commissioning of controller. All safety related instructions appearing in this manual must be followed to ensure safety of the operating personnel as well as the instrument.

General:
  • The controller must be configured correctly for intended operation. Incorrect configuration could result in damage to the equipment or the process under control or it may lead to personnel injury. 
  • The controller is generally part of control panel and in such a case the terminals should not remain accessible to the user after installation. 

Mechanical

  • The Controller in its installed state must not come in close proximity to any corrosive/combustible gases, caustic vapors, oils, steam or any other process byproducts. 
  • The Controller in its installed state should not be exposed to carbon dust, salt air, direct sunlight or radiant heat 
  • Ambient temperature and relative humidity surrounding the controller must not exceed the maximum specified limit for proper operation of the controller. 
  • The controller in its installed state must be protected against excessive electrostatic or electromagnetic interferences. Ventilation slits provided on the chassis of the instrument are meant for thermal dissipation hence should not be obstructed in the panel.

Electrical:
  • The controller must be wired as per wiring diagram & it must comply with local electrical regulation. 
  • Care must be taken not to connect AC supplies to low voltage sensor input. 
  • Circuit breaker or mains s/w with fuse (275V/1A) must be installed between power supply and supply terminals to protect the controller from any possible damage due to high voltage surges of extended duration. 
  • Circuit breaker and appropriate fuses must be used for driving high voltage loads to protect the controller from any possible damage due to short circuit on loads. 
  • To minimize pickup of electrical noise, the wiring for low voltage DC and sensor input must be routed away from high current power cables. Where it is impractical to do so, use shielded ground at both ends. 
  • The controller should not be wired to a 3-Phase supply with unearthed star connection. Under fault condition such supply could rise above 264 VAC which will damage the controller. 
  • The Electrical noise generated by switching inductive loads might create momentary Fluctuation in display, alarm latch up, data loss or permanent damage to the instrument. To reduce this use snubber circuit across the load. 
  • It is essential to install a over Temp. Protection device to avoid any failure of heating system. Apart from spoiling the product, this could damage the process being controlled.
Request
Callback
Yes! I am Interested

AI 5742 Digital Temperature Controller

AI 5742 Digital Temperature Controller
  • AI 5742 Digital Temperature Controller
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberAI 5742
BrandI Therm
Sampling Time125 msec
Weight200 gms
Display Height0.56 Inch
Resolution1 Deg C
Digital Filter1 to 10 Sec
Operating Range0 ~50 Deg C
Storage Humidity95% Rh (Non-condensing)
Supply Voltage90~270VAC
Frequency50-60 Hz
Power Consumption4 W

Safety Instruction:
  • This controller is meant for temperature control applications. It is important to read the manual prior to installing or commissioning of controller. All safety related instructions appearing in this manual must be followed to ensure safety of the operating personnel as well as the instrument.

General:
  • The controller must be configured correctly for intended operation. Incorrect configuration could result in damage to the equipment or the process under control or it may lead to personnel injury. 
  • The controller is generally part of control panel and in such a case the terminals should not remain accessible to the user after installation. 

Mechanical

  • The Controller in its installed state must not come in close proximity to any corrosive/combustible gases, caustic vapors, oils, steam or any other process byproducts. 
  • The Controller in its installed state should not be exposed to carbon dust, salt air, direct sunlight or radiant heat 
  • Ambient temperature and relative humidity surrounding the controller must not exceed the maximum specified limit for proper operation of the controller. 
  • The controller in its installed state must be protected against excessive electrostatic or electromagnetic interferences. Ventilation slits provided on the chassis of the instrument are meant for thermal dissipation hence should not be obstructed in the panel.

Electrical:
  • The controller must be wired as per wiring diagram & it must comply with local electrical regulation. 
  • Care must be taken not to connect AC supplies to low voltage sensor input. 
  • Circuit breaker or mains s/w with fuse (275V/1A) must be installed between power supply and supply terminals to protect the controller from any possible damage due to high voltage surges of extended duration. 
  • Circuit breaker and appropriate fuses must be used for driving high voltage loads to protect the controller from any possible damage due to short circuit on loads. 
  • To minimize pickup of electrical noise, the wiring for low voltage DC and sensor input must be routed away from high current power cables. Where it is impractical to do so, use shielded ground at both ends. 
  • The controller should not be wired to a 3-Phase supply with unearthed star connection. Under fault condition such supply could rise above 264 VAC which will damage the controller. 
  • The Electrical noise generated by switching inductive loads might create momentary Fluctuation in display, alarm latch up, data loss or permanent damage to the instrument. To reduce this use snubber circuit across the load. 
  • It is essential to install a over Temp. Protection device to avoid any failure of heating system. Apart from spoiling the product, this could damage the process being controlled.
Request
Callback
Yes! I am Interested

AI 5442 Digital Temperature Controller

AI 5442 Digital Temperature Controller
  • AI 5442 Digital Temperature Controller
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberAI 5442
BrandI Therm
Size48*48 mm
Sampling Time125 msec
Weight130 gm
Display Height0.36 Inch
Resolution1 Deg C
Digital Filter1 to 10 Sec
Drive Capacity12V @ 30mA
Operating Range0 ~50 Deg C
Storage Humidity95% Rh (Non-condensing)
Supply Voltage90~270 VAC
Frequency50-60 Hz
Power consumption4 W

Safety Instruction:
  • This controller is meant for temperature control applications. It is important to read the manual prior to installing or commissioning of controller. All safety related instructions appearing in this manual must be followed to ensure safety of the operating personnel as well as the instrument.

General:
  • The controller must be configured correctly for intended operation. Incorrect configuration could result in damage to the equipment or the process under control or it may lead to personnel injury. 
  • The controller is generally part of control panel and in such a case the terminals should not remain accessible to the user after installation. 

Mechanical

  • The Controller in its installed state must not come in close proximity to any corrosive/combustible gases, caustic vapors, oils, steam or any other process byproducts. 
  • The Controller in its installed state should not be exposed to carbon dust, salt air, direct sunlight or radiant heat 
  • Ambient temperature and relative humidity surrounding the controller must not exceed the maximum specified limit for proper operation of the controller. 
  • The controller in its installed state must be protected against excessive electrostatic or electromagnetic interferences. Ventilation slits provided on the chassis of the instrument are meant for thermal dissipation hence should not be obstructed in the panel.

Electrical:
  • The controller must be wired as per wiring diagram & it must comply with local electrical regulation. 
  • Care must be taken not to connect AC supplies to low voltage sensor input. 
  • Circuit breaker or mains s/w with fuse (275V/1A) must be installed between power supply and supply terminals to protect the controller from any possible damage due to high voltage surges of extended duration. 
  • Circuit breaker and appropriate fuses must be used for driving high voltage loads to protect the controller from any possible damage due to short circuit on loads. 
  • To minimize pickup of electrical noise, the wiring for low voltage DC and sensor input must be routed away from high current power cables. Where it is impractical to do so, use shielded ground at both ends. 
  • The controller should not be wired to a 3-Phase supply with unearthed star connection. Under fault condition such supply could rise above 264 VAC which will damage the controller. 
  • The Electrical noise generated by switching inductive loads might create momentary Fluctuation in display, alarm latch up, data loss or permanent damage to the instrument. To reduce this use snubber circuit across the load. 
  • It is essential to install a over Temp. Protection device to avoid any failure of heating system. Apart from spoiling the product, this could damage the process being controlled.
Request
Callback
Yes! I am Interested

KTC-44 Multifunction Timers and Counter

KTC-44 Multifunction Timers and Counter
  • KTC-44 Multifunction Timers and Counter
Get Best Quote
Approx. Price: Rs 2,000 / UnitGet Latest Price
Product Brochure

Product Details:

BrandI Therm
Model NumberKTC-44
Size48 X 48 mm
Display Height0.36 Inch
Reset TimeMore Than 100 ms
Timing Accuracy0.05% Full Scale
Repeat Accuracy0.01%
Power Supply90 to 270 VAC
Operating Temperature0 ~ 50 Deg C
Humidity95% Rh (Non Condensing)

Mechanical:
  • Ambient temperature and relative humidity surrounding the Controller must not exceed the maximum specified limits.
  • The Controller in its installed state must be protected against excessive electrostatic or electromagnetic interferences.

Electrical:
  • The Controller must be wired as per wiring diagram & it mustcomply with local electrical regulation.
  • The Electrical noise generated by switching inductive loadsmight create momentary Fluctuation in display, latch up, dataloss or permanent damage to the instrument. To reduce this usesnubber circuit across the load.
Request
Callback
Yes! I am Interested

CTR-33 Multifunction Timers and Counter

CTR-33 Multifunction Timers and Counter
  • CTR-33 Multifunction Timers and Counter
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Motor VoltageCTR-33
BrandI Therm
Size36 X 72 mm
Display Height0.39 Inch
Memory RetentionUp to 10 Year
Mains Supply90 to 270 V AC
Sensor Supply12VDC (+10%) @ 30mA
Accuracy0.05% FSD
Operating Temperature0-55 Deg C
Relative HumidityBelow 95 % RH

Safety Instruction:
  • This controller is meant for Counter, Timer & Rate Indicator applications. It is important to read the manual prior to installing or commissioning of controller. All safety related instruction appearing in this manual must be followed to ensure safety of the operating personnel as well as the instrument.

General:
  • The Controller must be configured correctly for intendedoperation. Incorrect configuration could result in damage tothe equipment or the process under control or it may leadpersonnel injury.
  • The Controller is generally part of control panel and insuch a case the terminals should not remain accessible tothe user after installation.

Mechanical:
  • The Controller in its installed state must not come inclose proximity to any corrosive/combustible gases, causticvapors, oils, steam or any other process by products.
  • The Controller in its installed state should not beexposed to carbon dust, salt air, direct sunlight.
  • Ambient temperature and relative humidity surrounding theController must not exceed the maximum specified limit f o rproper operation.
  • The Controller in its installed state must be protected againstelectromagnetic interferences. Ventilation holes provided onthe chassis of the instrument are meant for thermaldissipation hence should not be obstructed in the panel.

Electrical:
  • The Controller must be wired as per wiring diagram & itmust comply with local electrical regulation.
  • Care must be taken not to connect AC supplies to low voltagesensor input.
  • Circuit breaker or mains s/w with fuse (275V/1A) must beinstalled between power supply and supply terminals toprotect the Controller from any possible damage due tohigh voltage surges of extended duration.
  •  Circuit breaker and appropriate fuses must be used fordriving high voltage loads to protect the Controller from anypossible damage due to short circuit on loads.
  • To minimize pickup of electrical noise, the wiring for lowvoltage DC and sensor input must be routed away from highcurrent power cables. Where it is impractical to do this, useshielded ground at both ends.
  • The Controller should not be wired to a 3-Phase supplywith unearthed star connection. Under fault condition suchsupply could rise above 264 VAC which will damage theController.
  • The Electrical noise generated by switching inductive loadsmight create momentary Fluctuation in display, alarm latchup, data loss or permanent damage to the instrument. Toreduce this use snubber circuit across the load.
Request
Callback
Yes! I am Interested

CTR-44 Multifunction Timers and Counter

CTR-44 Multifunction Timers and Counter
  • CTR-44 Multifunction Timers and Counter
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Size48 x 48 mm
Accuracy0.05 % FSD
Model NumberCTR-44
Display Height0.30 Inch
Mains Supply90 to 270 V AC
Operating Temperature0 to 55 Deg C
Relative HumidityBelow 95 %RH

Safety Instruction:
  • This controller is meant for Counter, Timer & Rate Indicator applications. It is important to read the manual prior to installing or commissioning of controller. All safety related instruction appearing in this manual must be followed to ensure safety of the operating personnel as well as the instrument.

General:
  • The Controller must be configured correctly for intendedoperation. Incorrect configuration could result in damage tothe equipment or the process under control or it may leadpersonnel injury.
  • The Controller is generally part of control panel and insuch a case the terminals should not remain accessible tothe user after installation.

Mechanical:
  • The Controller in its installed state must not come inclose proximity to any corrosive/combustible gases, causticvapors, oils, steam or any other process by products.
  • The Controller in its installed state should not beexposed to carbon dust, salt air, direct sunlight.
  • Ambient temperature and relative humidity surrounding theController must not exceed the maximum specified limit f o rproper operation.
  • The Controller in its installed state must be protected againstelectromagnetic interferences. Ventilation holes provided onthe chassis of the instrument are meant for thermaldissipation hence should not be obstructed in the panel.

Electrical:
  • The Controller must be wired as per wiring diagram & itmust comply with local electrical regulation.
  • Care must be taken not to connect AC supplies to low voltagesensor input.
  • Circuit breaker or mains s/w with fuse (275V/1A) must beinstalled between power supply and supply terminals toprotect the Controller from any possible damage due tohigh voltage surges of extended duration.
  •  Circuit breaker and appropriate fuses must be used fordriving high voltage loads to protect the Controller from anypossible damage due to short circuit on loads.
  • To minimize pickup of electrical noise, the wiring for lowvoltage DC and sensor input must be routed away from highcurrent power cables. Where it is impractical to do this, useshielded ground at both ends.
  • The Controller should not be wired to a 3-Phase supplywith unearthed star connection. Under fault condition suchsupply could rise above 264 VAC which will damage theController.
  • The Electrical noise generated by switching inductive loadsmight create momentary Fluctuation in display, alarm latchup, data loss or permanent damage to the instrument. Toreduce this use snubber circuit across the load.
Request
Callback
Yes! I am Interested

CTR-77 Multifunction Timers and Counter

CTR-77 Multifunction Timers and Counter
  • CTR-77 Multifunction Timers and Counter
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberCTR-77
Size72 X 72 mm
Accuracy0.05 % FSD
BrandI Therm
Mains Supply90 to 270 V AC
Sensor Supply12 V DC (+10%) @ 30mA
MountingPanel
HousingABS Plastic
Operating Temperature0-55 Deg C

Safety Instruction:
  • This controller is meant for Counter, Timer & Rate Indicator applications. It is important to read the manual prior to installing or commissioning of controller. All safety related instruction appearing in this manual must be followed to ensure safety of the operating personnel as well as the instrument.

General:
  • The Controller must be configured correctly for intendedoperation. Incorrect configuration could result in damage tothe equipment or the process under control or it may leadpersonnel injury.
  • The Controller is generally part of control panel and insuch a case the terminals should not remain accessible tothe user after installation.

Mechanical:
  • The Controller in its installed state must not come inclose proximity to any corrosive/combustible gases, causticvapors, oils, steam or any other process by products.
  • The Controller in its installed state should not beexposed to carbon dust, salt air, direct sunlight.
  • Ambient temperature and relative humidity surrounding theController must not exceed the maximum specified limit f o rproper operation.
  • The Controller in its installed state must be protected againstelectromagnetic interferences. Ventilation holes provided onthe chassis of the instrument are meant for thermaldissipation hence should not be obstructed in the panel.

Electrical:
  • The Controller must be wired as per wiring diagram & itmust comply with local electrical regulation.
  • Care must be taken not to connect AC supplies to low voltagesensor input.
  • Circuit breaker or mains s/w with fuse (275V/1A) must beinstalled between power supply and supply terminals toprotect the Controller from any possible damage due tohigh voltage surges of extended duration.
  •  Circuit breaker and appropriate fuses must be used fordriving high voltage loads to protect the Controller from anypossible damage due to short circuit on loads.
  • To minimize pickup of electrical noise, the wiring for lowvoltage DC and sensor input must be routed away from highcurrent power cables. Where it is impractical to do this, useshielded ground at both ends.
  • The Controller should not be wired to a 3-Phase supplywith unearthed star connection. Under fault condition suchsupply could rise above 264 VAC which will damage theController.
  • The Electrical noise generated by switching inductive loadsmight create momentary Fluctuation in display, alarm latchup, data loss or permanent damage to the instrument. Toreduce this use snubber circuit across the load.
Request
Callback
Yes! I am Interested

CTR-88 Multifunction Timers and Counter

CTR-88 Multifunction Timers and Counter
  • CTR-88 Multifunction Timers and Counter
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberCTR-88
Size48 X 96 mm
Accuracy0.05% FSD
BrandI Therm
Mains Supply90 to 270 V AC
Sensor Supply12VDC (+10%) @ 30mA
MountingPanel Mounting
Operating Temperature0 to 55 Deg C
Relative HumidityBelow 95 % RH

Safety Instruction:
  • This controller is meant for Counter, Timer & Rate Indicator applications. It is important to read the manual prior to installing or commissioning of controller. All safety related instruction appearing in this manual must be followed to ensure safety of the operating personnel as well as the instrument.

General:
  • The Controller must be configured correctly for intendedoperation. Incorrect configuration could result in damage tothe equipment or the process under control or it may leadpersonnel injury.
  • The Controller is generally part of control panel and insuch a case the terminals should not remain accessible tothe user after installation.

Mechanical:
  • The Controller in its installed state must not come inclose proximity to any corrosive/combustible gases, causticvapors, oils, steam or any other process by products.
  • The Controller in its installed state should not beexposed to carbon dust, salt air, direct sunlight.
  • Ambient temperature and relative humidity surrounding theController must not exceed the maximum specified limit f o rproper operation.
  • The Controller in its installed state must be protected againstelectromagnetic interferences. Ventilation holes provided onthe chassis of the instrument are meant for thermaldissipation hence should not be obstructed in the panel.

Electrical:
  • The Controller must be wired as per wiring diagram & itmust comply with local electrical regulation.
  • Care must be taken not to connect AC supplies to low voltagesensor input.
  • Circuit breaker or mains s/w with fuse (275V/1A) must beinstalled between power supply and supply terminals toprotect the Controller from any possible damage due tohigh voltage surges of extended duration.
  •  Circuit breaker and appropriate fuses must be used fordriving high voltage loads to protect the Controller from anypossible damage due to short circuit on loads.
  • To minimize pickup of electrical noise, the wiring for lowvoltage DC and sensor input must be routed away from highcurrent power cables. Where it is impractical to do this, useshielded ground at both ends.
  • The Controller should not be wired to a 3-Phase supplywith unearthed star connection. Under fault condition suchsupply could rise above 264 VAC which will damage theController.
  • The Electrical noise generated by switching inductive loadsmight create momentary Fluctuation in display, alarm latchup, data loss or permanent damage to the instrument. Toreduce this use snubber circuit across the load.
Request
Callback
Yes! I am Interested

CTR-99 Multifunction Timers and Counter

CTR-99 Multifunction Timers and Counter
  • CTR-99 Multifunction Timers and Counter
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberCTR-99
Size96 x 96 mm
Accuracy0.05 % FSD
BrandI Therm
Display Height0.56 Inch
Mains Supply90 to 270 V AC
Sensor Supply12VDC (+10%) @ 30mA
Operating Temperature0-55 Deg C
Relative HumidityBelow 95 % RH

Safety Instruction:
  • This controller is meant for Counter, Timer & Rate Indicator applications. It is important to read the manual prior to installing or commissioning of controller. All safety related instruction appearing in this manual must be followed to ensure safety of the operating personnel as well as the instrument.

General:
  • The Controller must be configured correctly for intendedoperation. Incorrect configuration could result in damage tothe equipment or the process under control or it may leadpersonnel injury.
  • The Controller is generally part of control panel and insuch a case the terminals should not remain accessible tothe user after installation.

Mechanical:
  • The Controller in its installed state must not come inclose proximity to any corrosive/combustible gases, causticvapors, oils, steam or any other process by products.
  • The Controller in its installed state should not beexposed to carbon dust, salt air, direct sunlight.
  • Ambient temperature and relative humidity surrounding theController must not exceed the maximum specified limit f o rproper operation.
  • The Controller in its installed state must be protected againstelectromagnetic interferences. Ventilation holes provided onthe chassis of the instrument are meant for thermaldissipation hence should not be obstructed in the panel.

Electrical:
  • The Controller must be wired as per wiring diagram & itmust comply with local electrical regulation.
  • Care must be taken not to connect AC supplies to low voltagesensor input.
  • Circuit breaker or mains s/w with fuse (275V/1A) must beinstalled between power supply and supply terminals toprotect the Controller from any possible damage due tohigh voltage surges of extended duration.
  •  Circuit breaker and appropriate fuses must be used fordriving high voltage loads to protect the Controller from anypossible damage due to short circuit on loads.
  • To minimize pickup of electrical noise, the wiring for lowvoltage DC and sensor input must be routed away from highcurrent power cables. Where it is impractical to do this, useshielded ground at both ends.
  • The Controller should not be wired to a 3-Phase supplywith unearthed star connection. Under fault condition suchsupply could rise above 264 VAC which will damage theController.
  • The Electrical noise generated by switching inductive loadsmight create momentary Fluctuation in display, alarm latchup, data loss or permanent damage to the instrument. Toreduce this use snubber circuit across the load.
Request
Callback
Yes! I am Interested

KTC-77 Multifunction Timers and Counter

KTC-77 Multifunction Timers and Counter
  • KTC-77 Multifunction Timers and Counter
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberKTC-77
Size72 X 72 mm
Humidity95% RN (Non Condensing)
BrandI Therm
Display Height0.56 Inch
Reset TimeMore Than 100 ms
Timing Accuracy0.05% Full Scale
Repeat Accuracy0.01%
Supply90 to 270 VAC
MountingPanel
HousingABS Plastic
Operating Temperature0 ~ 50 Deg C

Mechanical:
  • Ambient temperature and relative humidity surrounding the Controller must not exceed the maximum specified limits.
  • The Controller in its installed state must be protected against excessive electrostatic or electromagnetic interferences.

Electrical:
  • The Controller must be wired as per wiring diagram & it mustcomply with local electrical regulation.
  • The Electrical noise generated by switching inductive loadsmight create momentary Fluctuation in display, latch up, dataloss or permanent damage to the instrument. To reduce this usesnubber circuit across the load.
Request
Callback
Yes! I am Interested

KTC-99 Multifunction Timers and Counter

KTC-99 Multifunction Timers and Counter
  • KTC-99 Multifunction Timers and Counter
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberKTC-99
Size96 x 96 mm
BrandI Therm
Display Height0.80 Inch
Reset TimeMore Than 100 ms
Timing Accuracy0.05% Full Scale
Repeat Accuracy0.01%
Supply90 to 270 V AC
MountingPanel
Operating Temperature0 ~ 50 Deg C

Mechanical:
  • Ambient temperature and relative humidity surrounding the Controller must not exceed the maximum specified limits.
  • The Controller in its installed state must be protected against excessive electrostatic or electromagnetic interferences.

Electrical:
  • The Controller must be wired as per wiring diagram & it mustcomply with local electrical regulation.
  • The Electrical noise generated by switching inductive loadsmight create momentary Fluctuation in display, latch up, dataloss or permanent damage to the instrument. To reduce this usesnubber circuit across the load.
Request
Callback
Yes! I am Interested

XTC-774 Multifunction Timers and Counter

XTC-774 Multifunction Timers and Counter
  • XTC-774 Multifunction Timers and Counter
Get Best Quote
Approx. Price: Rs 20,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberXTC-774
Size72 x 72 mm
BrandI Therm
Reset TimeMore Than 100 ms
Timing Accuracy0.05% Full Scale
Repeat Accuracy0.01%
Supply Voltage90 to 270 VAC
Operating Temperature0 ~ 50 Deg C
Humidity95% Rh

Installation Guidelines:
  • Prepare the cut-out with proper dimension as shown in figure.
  • Remove clamp from Controller.
  • Push the Timer through panel cut-out and secure the Controller in its place by tightening the side clamp.

Mechanical:
  • Ambient temperature and relative humidity surrounding the Controller must not exceed the maximum specified limits..
  • The Controller in its installed state must be protected against excessive electrostatic or electromagnetic interferences.

Electrical:
  • The Controller must be wired as per wiring diagram & it must comply with local electrical regulation.
  • The Electrical noise generated by switching inductive loads might create momentary Fluctuation in display, latch up, data loss or permanent damage to the instrument. To reduce this use snubber circuit across the load.
Request
Callback
Yes! I am Interested

BL-44 Counter Timer

BL-44 Counter Timer
  • BL-44 Counter Timer
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberBL-44
Size48 X 48 Inch
Accuracy0.05 % Full Scale
Memory RetentionUp to 10 Year
Sensor Supply12 V DC (+-10%) @ 30 mA
Humidity95 % RN
BrandI Therm
Supply Voltage90 to 270 V AC
Operating Temperature0-55 Deg C

Safety Instruction:
  • This Controller Is Meant For Batch & Length Counter Applications. It Is Important To Read The Manual Prior To Installing Or Commissioning Of Controller. All Safety Related Instruction Appearing In This Manual Must Be Followed To Ensure Safety Of The Operating Personnel As Well As The Instrument.

General:
  • The Controller Must Be Configured Correctly For Intended Operation. Incorrect Configuration Could Result In Damage To The
  • Equipment Or The Process Under Control Or It May Lead Personnel Injury.
  • The Controller Is Generally Part Of Control Panel And In Such A Case The Terminals Should Not Remain Accessible To The User After Installation.

Mechanical:
  • The Controller In Its Installed State Must Not Come In Close Proximity To Any Corrosive/combustible Gases, Caustic Vapors, Oils, Steam Or Any Other Process By Products.
  • The Controller In Its Installed State Should Not Be Exposed To Carbon Dust, Salt Air, Direct Sunlight Or Radiant Heat.
  • Ambient Temperature And Relative Humidity Surrounding The Controller Must Not Exceed The Maximum Specified Limit For Proper Operation Of The Controller.
  • The Controller In Its Installed State Must Be Protected Against Excessive Electrostatic Or Electromagnetic Interferences. Ventilation Holes Provided On The Chassis Of The Instrument Are Meant For Thermal Dissipation Hence Should Not Be Obstructed In The Panel.

Electrical:
  • The controller must be wired as per wiring diagram & it must comply with local electrical regulation. Care must be taken not to connect AC supplies to low voltage sensor input. 
  • Circuit breaker or mains s/w with fuse (275V/1A) must be installed between power supply and supply terminals to protect the controller from any possible damage due to high voltage surges of extended duration. 
  • Circuit breaker and appropriate fuses must be used for driving high voltage loads to protect the controller from any possible damage due to short circuit on loads. 
  • To minimize pickup of electrical noise, the wiring for low voltage DC and sensor input must be routed away from high current power cables. Where it is impractical to do this, use shielded ground at both ends. 
  • The controller should not be wired to a 3-Phase supply with unearthed star connection. Under fault condition such supply could rise above 264 VAC which will damage the controller. 
  • The Electrical noise generated by switching inductive loads might create momentary Fluctuation in display, alarm latch up, data loss or permanent damage to the instrument. To reduce this use snubber circuit across the load. 
Request
Callback
Yes! I am Interested

XTC-994 Multifunction Timers and Counter

XTC-994 Multifunction Timers and Counter
  • XTC-994 Multifunction Timers and Counter
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberXTC-994
Size96 x 96 mm
BrandI Therm
Reset TimeMore Than 100 ms
Timing Accuracy0.05% Full Scale
Repeat Accuracy0.01%
Supply Voltage90 to 270 V AC
MountingPanel
Operating Temperature0-50 Deg C
Humidity95 % RH

Installation Guidelines:
  • Prepare the cut-out with proper dimension as shown in figure.
  • Remove clamp from Controller.
  • Push the Timer through panel cut-out and secure the Controller in its place by tightening the side clamp.

Mechanical:
  • Ambient temperature and relative humidity surrounding the Controller must not exceed the maximum specified limits..
  • The Controller in its installed state must be protected against excessive electrostatic or electromagnetic interferences.

Electrical:
  • The Controller must be wired as per wiring diagram & it must comply with local electrical regulation.
  • The Electrical noise generated by switching inductive loads might create momentary Fluctuation in display, latch up, data loss or permanent damage to the instrument. To reduce this use snubber circuit across the load.
Request
Callback
Yes! I am Interested

AI 7482 PID Temperature Controller

AI 7482 PID Temperature Controller
  • AI 7482 PID Temperature Controller
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberAI 7482
BrandI Therm
Size48*48 mm
Sampling Time125 msec
Display Height0.36 Inch
Resolution1 Deg C
Digital Filter1 to 10 Sec
Drive Capacity12V @ 30mA
Operating Range0 ~50 Deg C
Storage Humidity95% Rh (Non-condensing)
Supply Voltage90~270 VAC
Frequency50-60 Hz
Power consumption4 W

Safety Instruction:
  • This controller is meant for Counter, Timer & Rate Indicator applications. It is important to read the manual prior to installing or commissioning of controller. All safety related instruction appearing in this manual must be followed to ensure safety of the operating personnel as well as the instrument.

General:
  • The Controller must be configured correctly for intendedoperation. Incorrect configuration could result in damage tothe equipment or the process under control or it may leadpersonnel injury.
  • The Controller is generally part of control panel and insuch a case the terminals should not remain accessible tothe user after installation.

Mechanical:
  • The Controller in its installed state must not come inclose proximity to any corrosive/combustible gases, causticvapors, oils, steam or any other process by products.
  • The Controller in its installed state should not beexposed to carbon dust, salt air, direct sunlight.
  • Ambient temperature and relative humidity surrounding theController must not exceed the maximum specified limit f o rproper operation.
  • The Controller in its installed state must be protected againstelectromagnetic interferences. Ventilation holes provided onthe chassis of the instrument are meant for thermaldissipation hence should not be obstructed in the panel.

Electrical:
  • The Controller must be wired as per wiring diagram & itmust comply with local electrical regulation.
  • Care must be taken not to connect AC supplies to low voltagesensor input.
  • Circuit breaker or mains s/w with fuse (275V/1A) must beinstalled between power supply and supply terminals toprotect the Controller from any possible damage due tohigh voltage surges of extended duration.
  •  Circuit breaker and appropriate fuses must be used fordriving high voltage loads to protect the Controller from anypossible damage due to short circuit on loads.
  • To minimize pickup of electrical noise, the wiring for lowvoltage DC and sensor input must be routed away from highcurrent power cables. Where it is impractical to do this, useshielded ground at both ends.
  • The Controller should not be wired to a 3-Phase supplywith unearthed star connection. Under fault condition suchsupply could rise above 264 VAC which will damage theController.
  • The Electrical noise generated by switching inductive loadsmight create momentary Fluctuation in display, alarm latchup, data loss or permanent damage to the instrument. Toreduce this use snubber circuit across the load.
Request
Callback
Yes! I am Interested

AI 7681 PID Temperature Controller

AI 7681 PID Temperature Controller
  • AI 7681 PID Temperature Controller
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberAI 7681
BrandI Therm
Size96*48 mm
Sampling Time125 msec
Display Height0.36 Inch
Resolution1 Deg C
Drive Capacity12V @ 30mA
Operating Range0 ~50 Deg C
Storage Humidity95% Rh (Non-condensing)
Supply Voltage90~270 VAC
Frequency50-60 Hz
Power consumption4 W

Safety Instruction:
  • This controller is meant for Counter, Timer & Rate Indicator applications. It is important to read the manual prior to installing or commissioning of controller. All safety related instruction appearing in this manual must be followed to ensure safety of the operating personnel as well as the instrument.

General:
  • The Controller must be configured correctly for intendedoperation. Incorrect configuration could result in damage tothe equipment or the process under control or it may leadpersonnel injury.
  • The Controller is generally part of control panel and insuch a case the terminals should not remain accessible tothe user after installation.

Mechanical:
  • The Controller in its installed state must not come inclose proximity to any corrosive/combustible gases, causticvapors, oils, steam or any other process by products.
  • The Controller in its installed state should not beexposed to carbon dust, salt air, direct sunlight.
  • Ambient temperature and relative humidity surrounding theController must not exceed the maximum specified limit f o rproper operation.
  • The Controller in its installed state must be protected againstelectromagnetic interferences. Ventilation holes provided onthe chassis of the instrument are meant for thermaldissipation hence should not be obstructed in the panel.

Electrical:
  • The Controller must be wired as per wiring diagram & itmust comply with local electrical regulation.
  • Care must be taken not to connect AC supplies to low voltagesensor input.
  • Circuit breaker or mains s/w with fuse (275V/1A) must beinstalled between power supply and supply terminals toprotect the Controller from any possible damage due tohigh voltage surges of extended duration.
  •  Circuit breaker and appropriate fuses must be used fordriving high voltage loads to protect the Controller from anypossible damage due to short circuit on loads.
  • To minimize pickup of electrical noise, the wiring for lowvoltage DC and sensor input must be routed away from highcurrent power cables. Where it is impractical to do this, useshielded ground at both ends.
  • The Controller should not be wired to a 3-Phase supplywith unearthed star connection. Under fault condition suchsupply could rise above 264 VAC which will damage theController.
  • The Electrical noise generated by switching inductive loadsmight create momentary Fluctuation in display, alarm latchup, data loss or permanent damage to the instrument. Toreduce this use snubber circuit across the load.
Request
Callback
Yes! I am Interested

AI 7841 PID Temperature Controller

AI 7841 PID Temperature Controller
  • AI 7841 PID Temperature Controller
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberAI 7841
BrandI Therm
Size48*96 mm
Sampling Time125 msec
Display Height0.56 Inch
Resolution1 Deg C
Drive Capacity12V @ 30mA
Operating Range0 ~50 Deg C
Storage Humidity95% Rh (Non-condensing)
Supply Voltage90~270 VAC
Frequency50-60 Hz
Power consumption4 W

Safety Instruction:
  • This controller is meant for Counter, Timer & Rate Indicator applications. It is important to read the manual prior to installing or commissioning of controller. All safety related instruction appearing in this manual must be followed to ensure safety of the operating personnel as well as the instrument.

General:
  • The Controller must be configured correctly for intendedoperation. Incorrect configuration could result in damage tothe equipment or the process under control or it may leadpersonnel injury.
  • The Controller is generally part of control panel and insuch a case the terminals should not remain accessible tothe user after installation.

Mechanical:
  • The Controller in its installed state must not come inclose proximity to any corrosive/combustible gases, causticvapors, oils, steam or any other process by products.
  • The Controller in its installed state should not beexposed to carbon dust, salt air, direct sunlight.
  • Ambient temperature and relative humidity surrounding theController must not exceed the maximum specified limit f o rproper operation.
  • The Controller in its installed state must be protected againstelectromagnetic interferences. Ventilation holes provided onthe chassis of the instrument are meant for thermaldissipation hence should not be obstructed in the panel.

Electrical:
  • The Controller must be wired as per wiring diagram & itmust comply with local electrical regulation.
  • Care must be taken not to connect AC supplies to low voltagesensor input.
  • Circuit breaker or mains s/w with fuse (275V/1A) must beinstalled between power supply and supply terminals toprotect the Controller from any possible damage due tohigh voltage surges of extended duration.
  •  Circuit breaker and appropriate fuses must be used fordriving high voltage loads to protect the Controller from anypossible damage due to short circuit on loads.
  • To minimize pickup of electrical noise, the wiring for lowvoltage DC and sensor input must be routed away from highcurrent power cables. Where it is impractical to do this, useshielded ground at both ends.
  • The Controller should not be wired to a 3-Phase supplywith unearthed star connection. Under fault condition suchsupply could rise above 264 VAC which will damage theController.
  • The Electrical noise generated by switching inductive loadsmight create momentary Fluctuation in display, alarm latchup, data loss or permanent damage to the instrument. Toreduce this use snubber circuit across the load.
Request
Callback
Yes! I am Interested

AI 7441 PID Temperature Controller

AI 7441 PID Temperature Controller
  • AI 7441 PID Temperature Controller
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberAI 7441
BrandI Therm
Size48*48 mm
Sampling Time125 msec
Display Height0.36 Inch
Resolution1 Deg C
Drive Capacity12V @ 30mA
Operating Range0 ~50 Deg C
Storage Humidity95% Rh (Non-condensing)
Supply Voltage90~270 VAC
Frequency50-60 Hz
Power Consumption4 W

Safety Instruction:
  • This controller is meant for Counter, Timer & Rate Indicator applications. It is important to read the manual prior to installing or commissioning of controller. All safety related instruction appearing in this manual must be followed to ensure safety of the operating personnel as well as the instrument.

General:
  • The Controller must be configured correctly for intendedoperation. Incorrect configuration could result in damage tothe equipment or the process under control or it may leadpersonnel injury.
  • The Controller is generally part of control panel and insuch a case the terminals should not remain accessible tothe user after installation.

Mechanical:
  • The Controller in its installed state must not come inclose proximity to any corrosive/combustible gases, causticvapors, oils, steam or any other process by products.
  • The Controller in its installed state should not beexposed to carbon dust, salt air, direct sunlight.
  • Ambient temperature and relative humidity surrounding theController must not exceed the maximum specified limit f o rproper operation.
  • The Controller in its installed state must be protected againstelectromagnetic interferences. Ventilation holes provided onthe chassis of the instrument are meant for thermaldissipation hence should not be obstructed in the panel.

Electrical:
  • The Controller must be wired as per wiring diagram & itmust comply with local electrical regulation.
  • Care must be taken not to connect AC supplies to low voltagesensor input.
  • Circuit breaker or mains s/w with fuse (275V/1A) must beinstalled between power supply and supply terminals toprotect the Controller from any possible damage due tohigh voltage surges of extended duration.
  •  Circuit breaker and appropriate fuses must be used fordriving high voltage loads to protect the Controller from anypossible damage due to short circuit on loads.
  • To minimize pickup of electrical noise, the wiring for lowvoltage DC and sensor input must be routed away from highcurrent power cables. Where it is impractical to do this, useshielded ground at both ends.
  • The Controller should not be wired to a 3-Phase supplywith unearthed star connection. Under fault condition suchsupply could rise above 264 VAC which will damage theController.
  • The Electrical noise generated by switching inductive loadsmight create momentary Fluctuation in display, alarm latchup, data loss or permanent damage to the instrument. Toreduce this use snubber circuit across the load.
  • It is essential to install a over Temp. Protection device to avoid any failure of heating system. Apart from spoiling the product, this could damage the process being controlled.
Request
Callback
Yes! I am Interested

AI 7882 PID Temperature Controller

AI 7882 PID Temperature Controller
  • AI 7882 PID Temperature Controller
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberAI 7882
BrandI Therm
Size48*96 mm
Sampling Time125 msec
Display Height0.36 Inch
Resolution1 Deg C
Drive Capacity12V @ 30mA
Operating Range0 ~50 Deg C
Storage Humidity95% Rh (Non-condensing)
Supply Voltage90~270 VAC
Frequency50-60 Hz
Power Consumption4 W

Safety Instruction:
  • This controller is meant for Counter, Timer & Rate Indicator applications. It is important to read the manual prior to installing or commissioning of controller. All safety related instruction appearing in this manual must be followed to ensure safety of the operating personnel as well as the instrument.

General:
  • The Controller must be configured correctly for intendedoperation. Incorrect configuration could result in damage tothe equipment or the process under control or it may leadpersonnel injury.
  • The Controller is generally part of control panel and insuch a case the terminals should not remain accessible tothe user after installation.

Mechanical:
  • The Controller in its installed state must not come inclose proximity to any corrosive/combustible gases, causticvapors, oils, steam or any other process by products.
  • The Controller in its installed state should not beexposed to carbon dust, salt air, direct sunlight.
  • Ambient temperature and relative humidity surrounding theController must not exceed the maximum specified limit f o rproper operation.
  • The Controller in its installed state must be protected againstelectromagnetic interferences. Ventilation holes provided onthe chassis of the instrument are meant for thermaldissipation hence should not be obstructed in the panel.

Electrical:
  • The Controller must be wired as per wiring diagram & itmust comply with local electrical regulation.
  • Care must be taken not to connect AC supplies to low voltagesensor input.
  • Circuit breaker or mains s/w with fuse (275V/1A) must beinstalled between power supply and supply terminals toprotect the Controller from any possible damage due tohigh voltage surges of extended duration.
  •  Circuit breaker and appropriate fuses must be used fordriving high voltage loads to protect the Controller from anypossible damage due to short circuit on loads.
  • To minimize pickup of electrical noise, the wiring for lowvoltage DC and sensor input must be routed away from highcurrent power cables. Where it is impractical to do this, useshielded ground at both ends.
  • The Controller should not be wired to a 3-Phase supplywith unearthed star connection. Under fault condition suchsupply could rise above 264 VAC which will damage theController.
  • The Electrical noise generated by switching inductive loadsmight create momentary Fluctuation in display, alarm latchup, data loss or permanent damage to the instrument. Toreduce this use snubber circuit across the load.
  • It is essential to install a over Temp. Protection device to avoid any failure of heating system. Apart from spoiling the product, this could damage the process being controlled.
Request
Callback
Yes! I am Interested

AI 7881 PID Temperature Controller

AI 7881 PID Temperature Controller
  • AI 7881 PID Temperature Controller
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberAI 7881
BrandI Therm
Size48*96 mm
Sampling Time125 msec
Display Height0.36 Inch
Resolution1 Deg C
Drive Capacity12V @ 30mA
Operating Range0 ~50 Deg C
Storage Humidity95% Rh (Non-condensing)
Supply Voltage90~270 VAC
Frequency50-60 Hz
Power Consumption4 W

Safety Instruction:
  • This controller is meant for Counter, Timer & Rate Indicator applications. It is important to read the manual prior to installing or commissioning of controller. All safety related instruction appearing in this manual must be followed to ensure safety of the operating personnel as well as the instrument.

General:
  • The Controller must be configured correctly for intendedoperation. Incorrect configuration could result in damage tothe equipment or the process under control or it may leadpersonnel injury.
  • The Controller is generally part of control panel and insuch a case the terminals should not remain accessible tothe user after installation.

Mechanical:
  • The Controller in its installed state must not come inclose proximity to any corrosive/combustible gases, causticvapors, oils, steam or any other process by products.
  • The Controller in its installed state should not beexposed to carbon dust, salt air, direct sunlight.
  • Ambient temperature and relative humidity surrounding theController must not exceed the maximum specified limit f o rproper operation.
  • The Controller in its installed state must be protected againstelectromagnetic interferences. Ventilation holes provided onthe chassis of the instrument are meant for thermaldissipation hence should not be obstructed in the panel.

Electrical:
  • The Controller must be wired as per wiring diagram & itmust comply with local electrical regulation.
  • Care must be taken not to connect AC supplies to low voltagesensor input.
  • Circuit breaker or mains s/w with fuse (275V/1A) must beinstalled between power supply and supply terminals toprotect the Controller from any possible damage due tohigh voltage surges of extended duration.
  •  Circuit breaker and appropriate fuses must be used fordriving high voltage loads to protect the Controller from anypossible damage due to short circuit on loads.
  • To minimize pickup of electrical noise, the wiring for lowvoltage DC and sensor input must be routed away from highcurrent power cables. Where it is impractical to do this, useshielded ground at both ends.
  • The Controller should not be wired to a 3-Phase supplywith unearthed star connection. Under fault condition suchsupply could rise above 264 VAC which will damage theController.
  • The Electrical noise generated by switching inductive loadsmight create momentary Fluctuation in display, alarm latchup, data loss or permanent damage to the instrument. Toreduce this use snubber circuit across the load.
Request
Callback
Yes! I am Interested

AI 7682 PID Temperature Controller

AI 7682 PID Temperature Controller
  • AI 7682 PID Temperature Controller
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberAI 7682
BrandI Therm
Size96*48 mm
Sampling Time125 msec
Display Height0.36 Inch
Resolution1 Deg C
Drive Capacity12V @ 30mA
Operating Range0 ~50 Deg C
Storage Humidity95% Rh (Non-condensing)
Supply Voltage90~270 VAC
Frequency50-60 Hz
Power consumption4 W

Safety Instruction:
  • This controller is meant for Counter, Timer & Rate Indicator applications. It is important to read the manual prior to installing or commissioning of controller. All safety related instruction appearing in this manual must be followed to ensure safety of the operating personnel as well as the instrument.

General:
  • The Controller must be configured correctly for intendedoperation. Incorrect configuration could result in damage tothe equipment or the process under control or it may leadpersonnel injury.
  • The Controller is generally part of control panel and insuch a case the terminals should not remain accessible tothe user after installation.

Mechanical:
  • The Controller in its installed state must not come inclose proximity to any corrosive/combustible gases, causticvapors, oils, steam or any other process by products.
  • The Controller in its installed state should not beexposed to carbon dust, salt air, direct sunlight.
  • Ambient temperature and relative humidity surrounding theController must not exceed the maximum specified limit f o rproper operation.
  • The Controller in its installed state must be protected againstelectromagnetic interferences. Ventilation holes provided onthe chassis of the instrument are meant for thermaldissipation hence should not be obstructed in the panel.

Electrical:
  • The Controller must be wired as per wiring diagram & itmust comply with local electrical regulation.
  • Care must be taken not to connect AC supplies to low voltagesensor input.
  • Circuit breaker or mains s/w with fuse (275V/1A) must beinstalled between power supply and supply terminals toprotect the Controller from any possible damage due tohigh voltage surges of extended duration.
  •  Circuit breaker and appropriate fuses must be used fordriving high voltage loads to protect the Controller from anypossible damage due to short circuit on loads.
  • To minimize pickup of electrical noise, the wiring for lowvoltage DC and sensor input must be routed away from highcurrent power cables. Where it is impractical to do this, useshielded ground at both ends.
  • The Controller should not be wired to a 3-Phase supplywith unearthed star connection. Under fault condition suchsupply could rise above 264 VAC which will damage theController.
  • The Electrical noise generated by switching inductive loadsmight create momentary Fluctuation in display, alarm latchup, data loss or permanent damage to the instrument. Toreduce this use snubber circuit across the load.
Request
Callback
Yes! I am Interested

AI 7481 PID Temperature Controller

AI 7481 PID Temperature Controller
  • AI 7481 PID Temperature Controller
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberAI 7481
BrandI Therm
Size48*48 mm
Sampling Time125 msec
Display Height0.36 Inch
Resolution1 Deg C
Drive Capacity12V @ 30mA
Operating Range0 ~50 Deg C
Storage Humidity95% Rh (Non-condensing)
Supply Voltage90~270 VAC
Frequency50-60 Hz
Power Consumption4 W

Safety Instruction:
  • This controller is meant for Counter, Timer & Rate Indicator applications. It is important to read the manual prior to installing or commissioning of controller. All safety related instruction appearing in this manual must be followed to ensure safety of the operating personnel as well as the instrument.

General:
  • The Controller must be configured correctly for intendedoperation. Incorrect configuration could result in damage tothe equipment or the process under control or it may leadpersonnel injury.
  • The Controller is generally part of control panel and insuch a case the terminals should not remain accessible tothe user after installation.

Mechanical:
  • The Controller in its installed state must not come inclose proximity to any corrosive/combustible gases, causticvapors, oils, steam or any other process by products.
  • The Controller in its installed state should not beexposed to carbon dust, salt air, direct sunlight.
  • Ambient temperature and relative humidity surrounding theController must not exceed the maximum specified limit f o rproper operation.
  • The Controller in its installed state must be protected againstelectromagnetic interferences. Ventilation holes provided onthe chassis of the instrument are meant for thermaldissipation hence should not be obstructed in the panel.

Electrical:
  • The Controller must be wired as per wiring diagram & itmust comply with local electrical regulation.
  • Care must be taken not to connect AC supplies to low voltagesensor input.
  • Circuit breaker or mains s/w with fuse (275V/1A) must beinstalled between power supply and supply terminals toprotect the Controller from any possible damage due tohigh voltage surges of extended duration.
  •  Circuit breaker and appropriate fuses must be used fordriving high voltage loads to protect the Controller from anypossible damage due to short circuit on loads.
  • To minimize pickup of electrical noise, the wiring for lowvoltage DC and sensor input must be routed away from highcurrent power cables. Where it is impractical to do this, useshielded ground at both ends.
  • The Controller should not be wired to a 3-Phase supplywith unearthed star connection. Under fault condition suchsupply could rise above 264 VAC which will damage theController.
  • The Electrical noise generated by switching inductive loadsmight create momentary Fluctuation in display, alarm latchup, data loss or permanent damage to the instrument. Toreduce this use snubber circuit across the load.
Request
Callback
Yes! I am Interested

AI 7741 PID Temperature Controller

AI 7741 PID Temperature Controller
  • AI 7741 PID Temperature Controller
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberAI 7741
BrandI Therm
Sampling Time125 msec
Display Height0.56 Inch
Resolution1 Deg C
Drive Capacity12V @ 30 mA
Operating Range0 ~50 Deg C
Storage Humidity95% Rh (Non-condensing)
Supply Voltage90~270 VAC
Frequency50-60 Hz
Power Consumption4 W

Safety Instruction:
  • This controller is meant for Counter, Timer & Rate Indicator applications. It is important to read the manual prior to installing or commissioning of controller. All safety related instruction appearing in this manual must be followed to ensure safety of the operating personnel as well as the instrument.

General:
  • The Controller must be configured correctly for intendedoperation. Incorrect configuration could result in damage tothe equipment or the process under control or it may leadpersonnel injury.
  • The Controller is generally part of control panel and insuch a case the terminals should not remain accessible tothe user after installation.

Mechanical:
  • The Controller in its installed state must not come inclose proximity to any corrosive/combustible gases, causticvapors, oils, steam or any other process by products.
  • The Controller in its installed state should not beexposed to carbon dust, salt air, direct sunlight.
  • Ambient temperature and relative humidity surrounding theController must not exceed the maximum specified limit f o rproper operation.
  • The Controller in its installed state must be protected againstelectromagnetic interferences. Ventilation holes provided onthe chassis of the instrument are meant for thermaldissipation hence should not be obstructed in the panel.

Electrical:
  • The Controller must be wired as per wiring diagram & itmust comply with local electrical regulation.
  • Care must be taken not to connect AC supplies to low voltagesensor input.
  • Circuit breaker or mains s/w with fuse (275V/1A) must beinstalled between power supply and supply terminals toprotect the Controller from any possible damage due tohigh voltage surges of extended duration.
  •  Circuit breaker and appropriate fuses must be used fordriving high voltage loads to protect the Controller from anypossible damage due to short circuit on loads.
  • To minimize pickup of electrical noise, the wiring for lowvoltage DC and sensor input must be routed away from highcurrent power cables. Where it is impractical to do this, useshielded ground at both ends.
  • The Controller should not be wired to a 3-Phase supplywith unearthed star connection. Under fault condition suchsupply could rise above 264 VAC which will damage theController.
  • The Electrical noise generated by switching inductive loadsmight create momentary Fluctuation in display, alarm latchup, data loss or permanent damage to the instrument. Toreduce this use snubber circuit across the load.
Request
Callback
Yes! I am Interested

AI 7781 PID Temperature Controller

AI 7781 PID Temperature Controller
  • AI 7781 PID Temperature Controller
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberAI 7781
BrandI Therm
Size48*96 mm
Sampling Time125 msec
Display Height0.56 Inch
Resolution1 Deg C
Drive Capacity12V @ 30mA
Operating Range0 ~50 Deg C
Storage Humidity95% Rh (Non-condensing)
Supply Voltage90~270 VAC
Frequency50-60 Hz
Power Consumption4 W

Safety Instruction:
  • This controller is meant for Counter, Timer & Rate Indicator applications. It is important to read the manual prior to installing or commissioning of controller. All safety related instruction appearing in this manual must be followed to ensure safety of the operating personnel as well as the instrument.

General:
  • The Controller must be configured correctly for intendedoperation. Incorrect configuration could result in damage tothe equipment or the process under control or it may leadpersonnel injury.
  • The Controller is generally part of control panel and insuch a case the terminals should not remain accessible tothe user after installation.

Mechanical:
  • The Controller in its installed state must not come inclose proximity to any corrosive/combustible gases, causticvapors, oils, steam or any other process by products.
  • The Controller in its installed state should not beexposed to carbon dust, salt air, direct sunlight.
  • Ambient temperature and relative humidity surrounding theController must not exceed the maximum specified limit f o rproper operation.
  • The Controller in its installed state must be protected againstelectromagnetic interferences. Ventilation holes provided onthe chassis of the instrument are meant for thermaldissipation hence should not be obstructed in the panel.

Electrical:
  • The Controller must be wired as per wiring diagram & itmust comply with local electrical regulation.
  • Care must be taken not to connect AC supplies to low voltagesensor input.
  • Circuit breaker or mains s/w with fuse (275V/1A) must beinstalled between power supply and supply terminals toprotect the Controller from any possible damage due tohigh voltage surges of extended duration.
  •  Circuit breaker and appropriate fuses must be used fordriving high voltage loads to protect the Controller from anypossible damage due to short circuit on loads.
  • To minimize pickup of electrical noise, the wiring for lowvoltage DC and sensor input must be routed away from highcurrent power cables. Where it is impractical to do this, useshielded ground at both ends.
  • The Controller should not be wired to a 3-Phase supplywith unearthed star connection. Under fault condition suchsupply could rise above 264 VAC which will damage theController.
  • The Electrical noise generated by switching inductive loadsmight create momentary Fluctuation in display, alarm latchup, data loss or permanent damage to the instrument. Toreduce this use snubber circuit across the load.
  • It is essential to install a over Temp. Protection device to avoid any failure of heating system. Apart from spoiling the product, this could damage the process being controlled.
Request
Callback
Yes! I am Interested

AI 7782 PID Temperature Controller

AI 7782 PID Temperature Controller
  • AI 7782 PID Temperature Controller
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberAI 7782
BrandI Therm
Sampling Time125 msec
Display Height0.56 Inch
Resolution1 Deg C
Drive Capacity12V @ 30mA
Operating Range0 ~50 Deg C
Storage Humidity95% Rh (Non-condensing)
Supply Voltage90~270 VAC
Frequency50-60 Hz
Power Consumption4 W

Safety Instruction:
  • This controller is meant for Counter, Timer & Rate Indicator applications. It is important to read the manual prior to installing or commissioning of controller. All safety related instruction appearing in this manual must be followed to ensure safety of the operating personnel as well as the instrument.

General:
  • The Controller must be configured correctly for intendedoperation. Incorrect configuration could result in damage tothe equipment or the process under control or it may leadpersonnel injury.
  • The Controller is generally part of control panel and insuch a case the terminals should not remain accessible tothe user after installation.

Mechanical:
  • The Controller in its installed state must not come inclose proximity to any corrosive/combustible gases, causticvapors, oils, steam or any other process by products.
  • The Controller in its installed state should not beexposed to carbon dust, salt air, direct sunlight.
  • Ambient temperature and relative humidity surrounding theController must not exceed the maximum specified limit f o rproper operation.
  • The Controller in its installed state must be protected againstelectromagnetic interferences. Ventilation holes provided onthe chassis of the instrument are meant for thermaldissipation hence should not be obstructed in the panel.

Electrical:
  • The Controller must be wired as per wiring diagram & itmust comply with local electrical regulation.
  • Care must be taken not to connect AC supplies to low voltagesensor input.
  • Circuit breaker or mains s/w with fuse (275V/1A) must beinstalled between power supply and supply terminals toprotect the Controller from any possible damage due tohigh voltage surges of extended duration.
  •  Circuit breaker and appropriate fuses must be used fordriving high voltage loads to protect the Controller from anypossible damage due to short circuit on loads.
  • To minimize pickup of electrical noise, the wiring for lowvoltage DC and sensor input must be routed away from highcurrent power cables. Where it is impractical to do this, useshielded ground at both ends.
  • The Controller should not be wired to a 3-Phase supplywith unearthed star connection. Under fault condition suchsupply could rise above 264 VAC which will damage theController.
  • The Electrical noise generated by switching inductive loadsmight create momentary Fluctuation in display, alarm latchup, data loss or permanent damage to the instrument. Toreduce this use snubber circuit across the load.
  • It is essential to install a over Temp. Protection device to avoid any failure of heating system. Apart from spoiling the product, this could damage the process being controlled.
Request
Callback
Yes! I am Interested

Nx-761 PID Temperature Controller

Nx-761 PID Temperature Controller
  • Nx-761 PID Temperature Controller
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberNx-761
BrandI Therm
Sampling Time125 msec
Display Height0.56 Inch
Resolution1 Deg C
Drive Capacity12V @ 30mA
Operating Range0 ~50 Deg C
Storage Humidity95% Rh (Non-condensing)
Supply Voltage90~270 VAC
Frequency50-60 Hz
Power Consumption4 W

Mechanical:
  • Ambient Temperature And Relative Humidity Surrounding TheController Must Not Exceed The Maximum Specified Limits.
  • The Controller In Its Installed State Must Be Protected AgainstExcessive Electrostatic Or Electromagnetic Interferences.

Electrical:

  • The Controller Must Be Wired As Per Wiring Diagram & It MustComply With Local Electrical Regulation.
  • The Electrical Noise Generated By Switching Inductive LoadsMight Create Momentary Fluctuation In Display, Latch Up, Data Loss Or Permanent Damage To The Instrument. To Reduce This Use SnubberCircuit Across The Load.
Request
Callback
Yes! I am Interested

Nx-762 PID Temperature Controller

Nx-762 PID Temperature Controller
  • Nx-762 PID Temperature Controller
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberNx-762
BrandI Therm
Sampling Time125 msec
Display Height0.56 Inch
Resolution1 Deg C
Drive Capacity12V @ 30mA
Operating Range0 ~50 Deg C
Storage Humidity95% Rh (Non-condensing)
Supply Voltage90~270 VAC
Frequency50-60 Hz
Power Consumption4 W

Installation Guidelines:
  • Prepare The Cut-out With Proper Dimension As Shown In Figure.
  • Remove Clamp From Controller.
  • Push The Timer Through Panel Cut-out And Secure The Controller In Its Place By Tightening The Side Clamp

Mechanical:
  • Ambient Temperature And Relative Humidity Surrounding TheController Must Not Exceed The Maximum Specified Limits.
  • The Controller In Its Installed State Must Be Protected AgainstExcessive Electrostatic Or Electromagnetic Interferences.

Electrical:

  • The Controller Must Be Wired As Per Wiring Diagram & It MustComply With Local Electrical Regulation.
  • The Electrical Noise Generated By Switching Inductive LoadsMight Create Momentary Fluctuation In Display, Latch Up, Data Loss Or Permanent Damage To The Instrument. To Reduce This Use SnubberCircuit Across The Load.
Request
Callback
Yes! I am Interested

Nx-961 PID Temperature Controller

Nx-961 PID Temperature Controller
  • Nx-961 PID Temperature Controller
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberNx-961
BrandI Therm
Size96*96 mm
Sampling Time125 msec
Display Height0.80 Inch
Resolution1 Deg C
Drive Capacity12V @ 30 mA
Operating Range0 ~50 Deg C
Storage Humidity95% Rh (Non-condensing)
Supply Voltage90~270 VAC
Frequency50-60 Hz
Power Consumption4 W

Mechanical:
  • Ambient Temperature And Relative Humidity Surrounding TheController Must Not Exceed The Maximum Specified Limits.
  • The Controller In Its Installed State Must Be Protected AgainstExcessive Electrostatic Or Electromagnetic Interferences.

Electrical:

  • The Controller Must Be Wired As Per Wiring Diagram & It MustComply With Local Electrical Regulation.
  • The Electrical Noise Generated By Switching Inductive LoadsMight Create Momentary Fluctuation In Display, Latch Up, Data Loss Or Permanent Damage To The Instrument. To Reduce This Use SnubberCircuit Across The Load.
Request
Callback
Yes! I am Interested

Nx-962 PID Temperature Controller

Nx-962 PID Temperature Controller
  • Nx-962 PID Temperature Controller
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberNx-962
BrandI Therm
Size96*96 mm
Sampling Time125 msec
Display Height0.80 Inch
Resolution1 Deg C
Drive Capacity12V @ 30mA
Operating Range0 ~50 Deg C
Storage Humidity95% Rh (Non-condensing)
Supply Voltage90~270 VAC
Frequency50-60 Hz
Power Consumption4 W

Installation Guidelines:
  • Prepare The Cut-out With Proper Dimension As Shown In Figure.
  • Remove Clamp From Controller.
  • Push The Timer Through Panel Cut-out And Secure The Controller In Its Place By Tightening The Side Clamp

Mechanical:
  • Ambient Temperature And Relative Humidity Surrounding TheController Must Not Exceed The Maximum Specified Limits.
  • The Controller In Its Installed State Must Be Protected AgainstExcessive Electrostatic Or Electromagnetic Interferences.

Electrical:

  • The Controller Must Be Wired As Per Wiring Diagram & It MustComply With Local Electrical Regulation.
  • The Electrical Noise Generated By Switching Inductive LoadsMight Create Momentary Fluctuation In Display, Latch Up, Data Loss Or Permanent Damage To The Instrument. To Reduce This Use SnubberCircuit Across The Load.
Request
Callback
Yes! I am Interested

Nx-461 PID Temperature Controller

Nx-461 PID Temperature Controller
  • Nx-461 PID Temperature Controller
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberNx-461
BrandI Therm
Size48*48 mm
Sampling Time125 msec
Display Height0.39 Inch
Resolution1 Deg C
Drive Capacity12V @ 30 mA
Operating Range0 ~50 Deg C
Storage Humidity95% Rh (Non-condensing)
Supply Voltage90~270 VAC
Frequency50-60 Hz
Power Consumption4 W

Mechanical:
  • Ambient Temperature And Relative Humidity Surrounding TheController Must Not Exceed The Maximum Specified Limits.
  • The Controller In Its Installed State Must Be Protected AgainstExcessive Electrostatic Or Electromagnetic Interferences.

Electrical:

  • The Controller Must Be Wired As Per Wiring Diagram & It MustComply With Local Electrical Regulation.
  • The Electrical Noise Generated By Switching Inductive LoadsMight Create Momentary Fluctuation In Display, Latch Up, Data Loss Or Permanent Damage To The Instrument. To Reduce This Use SnubberCircuit Across The Load.
Request
Callback
Yes! I am Interested

Nx-462 PID Temperature Controller

Nx-462 PID Temperature Controller
  • Nx-462 PID Temperature Controller
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberNx-462
BrandI Therm
Size48*48 mm
Sampling Time125 msec
Display Height0.39 Inch
Resolution1 Deg C
Drive Capacity12V @ 30mA
Operating Range0 ~50 Deg C
Storage Humidity95% Rh (Non-condensing)
Supply Voltage90~270 VAC
Frequency50-60 Hz
Power Consumption4 W

Installation Guidelines:
  • Prepare The Cut-out With Proper Dimension As Shown In Figure.
  • Remove Clamp From Controller.
  • Push The Timer Through Panel Cut-out And Secure The Controller In Its Place By Tightening The Side Clamp

Mechanical:
  • Ambient Temperature And Relative Humidity Surrounding TheController Must Not Exceed The Maximum Specified Limits.
  • The Controller In Its Installed State Must Be Protected AgainstExcessive Electrostatic Or Electromagnetic Interferences.

Electrical:

  • The Controller Must Be Wired As Per Wiring Diagram & It MustComply With Local Electrical Regulation.
  • The Electrical Noise Generated By Switching Inductive LoadsMight Create Momentary Fluctuation In Display, Latch Up, Data Loss Or Permanent Damage To The Instrument. To Reduce This Use SnubberCircuit Across The Load.
Request
Callback
Yes! I am Interested

KTM 996 Digital Timer

KTM 996 Digital Timer
  • KTM 996 Digital Timer
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberKTM 996
BrandI Therm
Display Height0.80 Inch
Reset timeMore Than 100 ms
Timing Accuracy0.05% Full Scale
Repeat Accuracy0.01%
Supply Voltage90 to 270 VAC
MountingPanel
Operating Temperature0 ~ 50 Deg C
Humidity95% Rh (Non Condensing)

Installation Guidelines:
  • Prepare The Cut-out With Proper Dimension As Shown In Figure.
  • Remove Clamp From Controller
  • Push The Controller Through Panel Cut-out And Secure The Controller In Its Place By Tightening The Side Clamp.

Safety Instruction:
  • All Safety Related Instruction Appearing In This Manual Must Be
  • Followed To Ensure Safety Of The Operator As Well As The Unit..

Mechanical:
  • Ambient Temperature And Relative Humidity Surrounding The Timer Must Not Exceed The Maximum Specified Limits..
  • The Timer In Its Installed State Must Be Protected Against Excessive Electrostatic Or Electromagnetic Interferences. 

Electrical:

  • The Timer Must Be Wired As Per Wiring Diagram & It Must Comply With Local Electrical Regulation.
  • The Electrical Noise Generated By Switching Inductive Loads Might Create Momentary Fluctuation In Display, Latch Up, Data Loss Or Permanent Damage To The Instrument. To Reduce This Use Snubber Circuit Across The Load
Request
Callback
Yes! I am Interested

KTM 443 Digital Timer

KTM 443 Digital Timer
  • KTM 443 Digital Timer
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberKTM 443
Size48 x 48 mm
BrandI Therm
Display Height0.39 Inch
Reset TimeMore Than 100 ms
Timing Accuracy0.05% Full Scale
Repeat Accuracy0.01%
Supply Voltage90 to 270 VAC
MountingPanel
Operating Temperature0 ~ 50 Deg C
Humidity95 % RH

Installation Guidelines:
  • Prepare The Cut-out With Proper Dimension As Shown In Figure.
  • Remove Clamp From Controller
  • Push The Controller Through Panel Cut-out And Secure The Controller In Its Place By Tightening The Side Clamp.

Safety Instruction:
  • All Safety Related Instruction Appearing In This Manual Must Be
  • Followed To Ensure Safety Of The Operator As Well As The Unit..

Mechanical:
  • Ambient Temperature And Relative Humidity Surrounding The Timer Must Not Exceed The Maximum Specified Limits..
  • The Timer In Its Installed State Must Be Protected Against Excessive Electrostatic Or Electromagnetic Interferences. 

Electrical:

  • The Timer Must Be Wired As Per Wiring Diagram & It Must Comply With Local Electrical Regulation.
  • The Electrical Noise Generated By Switching Inductive Loads Might Create Momentary Fluctuation In Display, Latch Up, Data Loss Or Permanent Damage To The Instrument. To Reduce This Use Snubber Circuit Across The Load
Request
Callback
Yes! I am Interested

KTM 446 Digital Timer

KTM 446 Digital Timer
  • KTM 446 Digital Timer
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberKTM 446
Size48 x 48 mm
BrandI Therm
Display Height0.39 Inch
Reset TimeMore Than 100 ms
Timing Accuracy0.05% Full Scale
Repeat Accuracy0.01%
Supply Voltage90 to 270 VAC
MountingPanel
Operating Temperature0 ~ 50 Deg C
Humidity95 % RH

Installation Guidelines:
  • Prepare The Cut-out With Proper Dimension As Shown In Figure.
  • Remove Clamp From Controller
  • Push The Controller Through Panel Cut-out And Secure The Controller In Its Place By Tightening The Side Clamp.

Safety Instruction:
  • All Safety Related Instruction Appearing In This Manual Must Be
  • Followed To Ensure Safety Of The Operator As Well As The Unit..

Mechanical:
  • Ambient Temperature And Relative Humidity Surrounding The Timer Must Not Exceed The Maximum Specified Limits..
  • The Timer In Its Installed State Must Be Protected Against Excessive Electrostatic Or Electromagnetic Interferences. 

Electrical:

  • The Timer Must Be Wired As Per Wiring Diagram & It Must Comply With Local Electrical Regulation.
  • The Electrical Noise Generated By Switching Inductive Loads Might Create Momentary Fluctuation In Display, Latch Up, Data Loss Or Permanent Damage To The Instrument. To Reduce This Use Snubber Circuit Across The Load
Request
Callback
Yes! I am Interested

KTM 446 Digital Timer

KTM 446 Digital Timer
  • KTM 446 Digital Timer
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberKTM 666
Size96 x 48 mm
BrandI Therm
Display Height0.39 Inch
Reset TimeMore Than 100 ms
Timing Accuracy0.05% Full Scale
Repeat Accuracy0.01%
Supply Voltage90 to 270 VAC
MountingPanel
Operating Temperature0 ~ 50 Deg C
Humidity95 % RH

Installation Guidelines:
  • Prepare The Cut-out With Proper Dimension As Shown In Figure.
  • Remove Clamp From Controller
  • Push The Controller Through Panel Cut-out And Secure The Controller In Its Place By Tightening The Side Clamp.

Safety Instruction:
  • All Safety Related Instruction Appearing In This Manual Must Be
  • Followed To Ensure Safety Of The Operator As Well As The Unit..

Mechanical:
  • Ambient Temperature And Relative Humidity Surrounding The Timer Must Not Exceed The Maximum Specified Limits..
  • The Timer In Its Installed State Must Be Protected Against Excessive Electrostatic Or Electromagnetic Interferences. 

Electrical:

  • The Timer Must Be Wired As Per Wiring Diagram & It Must Comply With Local Electrical Regulation.
  • The Electrical Noise Generated By Switching Inductive Loads Might Create Momentary Fluctuation In Display, Latch Up, Data Loss Or Permanent Damage To The Instrument. To Reduce This Use Snubber Circuit Across The Load
Request
Callback
Yes! I am Interested

KTM 773 Digital Timer

KTM 773 Digital Timer
  • KTM 773 Digital Timer
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberKTM 773
Size72 x 72 mm
BrandI Therm
Display Height0.56 Inch
Reset TimeMore Than 100 ms
Timing Accuracy0.05% Full Scale
Repeat Accuracy0.01%
Supply Voltage90 to 270 VAC
MountingPanel
Operating Temperature0 ~ 50 Deg C
Humidity95 % RH

Installation Guidelines:
  • Prepare The Cut-out With Proper Dimension As Shown In Figure.
  • Remove Clamp From Controller
  • Push The Controller Through Panel Cut-out And Secure The Controller In Its Place By Tightening The Side Clamp.

Safety Instruction:
  • All Safety Related Instruction Appearing In This Manual Must Be
  • Followed To Ensure Safety Of The Operator As Well As The Unit..

Mechanical:
  • Ambient Temperature And Relative Humidity Surrounding The Timer Must Not Exceed The Maximum Specified Limits..
  • The Timer In Its Installed State Must Be Protected Against Excessive Electrostatic Or Electromagnetic Interferences. 

Electrical:

  • The Timer Must Be Wired As Per Wiring Diagram & It Must Comply With Local Electrical Regulation.
  • The Electrical Noise Generated By Switching Inductive Loads Might Create Momentary Fluctuation In Display, Latch Up, Data Loss Or Permanent Damage To The Instrument. To Reduce This Use Snubber Circuit Across The Load.
Request
Callback
Yes! I am Interested

KTM 776 Digital Timer

KTM 776 Digital Timer
  • KTM 776 Digital Timer
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price

Product Details:

Model Name/NumberKTM 776
Size72 x 72 mm
BrandI Therm
Display Height0.56 Inch
Reset TimeMore Than 100 ms
Timing Accuracy0.05% Full Scale
Repeat Accuracy0.01%
Supply Voltage90 to 270 VAC
MountingPanel
Operating Temperature0 ~ 50 Deg C
Humidity95 % RH

Installation Guidelines:
  • Prepare The Cut-out With Proper Dimension As Shown In Figure.
  • Remove Clamp From Controller
  • Push The Controller Through Panel Cut-out And Secure The Controller In Its Place By Tightening The Side Clamp.

Safety Instruction:
  • All Safety Related Instruction Appearing In This Manual Must Be
  • Followed To Ensure Safety Of The Operator As Well As The Unit..

Mechanical:
  • Ambient Temperature And Relative Humidity Surrounding The Timer Must Not Exceed The Maximum Specified Limits..
  • The Timer In Its Installed State Must Be Protected Against Excessive Electrostatic Or Electromagnetic Interferences. 

Electrical:

  • The Timer Must Be Wired As Per Wiring Diagram & It Must Comply With Local Electrical Regulation.
  • The Electrical Noise Generated By Switching Inductive Loads Might Create Momentary Fluctuation In Display, Latch Up, Data Loss Or Permanent Damage To The Instrument. To Reduce This Use Snubber Circuit Across The Load.
Request
Callback
Yes! I am Interested

KTM 993 Digital Timer

KTM 993 Digital Timer
  • KTM 993 Digital Timer
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberKTM 993
Size96 X 96 mm
BrandI Therm
Display Height0.56 Inch
Reset TimeMore Than 100 ms
Timing Accuracy0.05% Full Scale
Repeat Accuracy0.01%
Supply Voltage90 to 270 VAC
MountingPanel
Operating Temperature0 ~ 50 Deg C
Humidity95 % RH

Installation Guidelines:
  • Prepare The Cut-out With Proper Dimension As Shown In Figure.
  • Remove Clamp From Controller
  • Push The Controller Through Panel Cut-out And Secure The Controller In Its Place By Tightening The Side Clamp.

Safety Instruction:
  • All Safety Related Instruction Appearing In This Manual Must Be
  • Followed To Ensure Safety Of The Operator As Well As The Unit..

Mechanical:
  • Ambient Temperature And Relative Humidity Surrounding The Timer Must Not Exceed The Maximum Specified Limits..
  • The Timer In Its Installed State Must Be Protected Against Excessive Electrostatic Or Electromagnetic Interferences. 

Electrical:

  • The Timer Must Be Wired As Per Wiring Diagram & It Must Comply With Local Electrical Regulation.
  • The Electrical Noise Generated By Switching Inductive Loads Might Create Momentary Fluctuation In Display, Latch Up, Data Loss Or Permanent Damage To The Instrument. To Reduce This Use Snubber Circuit Across The Load.
Request
Callback
Yes! I am Interested

XT-43 Digital Timer

XT-43 Digital Timer
  • XT-43 Digital Timer
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberXT-43
Size48 x 48 mm
BrandI Therm
Reset Timemore Than 100 ms
Display Height0.39 Inch
Timing Accuracy0.05 % Full Scale
Repeat Accuracy0.01%
Supply Voltage90 to 270 V AC
MountingPanel
HousingABS Plastic
Operating Temperature0-50 Deg C
Humidity95 % RH

Mechanical:
  • Ambient Temperature And Relative Humidity Surrounding The Controller Must Not Exceed The Maximum Specified Limits.
  • The Controller In Its Installed State Must Be Protected Against Excessive Electrostatic Or Electromagnetic Interferences.

Electrical:
  • The Controller Must Be Wired As Per Wiring Diagram & It Must Comply With Local Electrical Regulation.
  • The Electrical Noise Generated By Switching Inductive Loads Might Create Momentary Fluctuation In Display, Latch Up, Data Loss Or Permanent Damage To The Instrument. To Reduce This Use Snubber Circuit Across The Load.
Request
Callback
Yes! I am Interested

XT-73 Digital Timer

XT-73 Digital Timer
  • XT-73 Digital Timer
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberXT-73
Size72 x 72 mm
BrandI Therm
Display Height0.56 Inch
Reset TimeMore Than 100 ms
Timing Accuracy0.05 % Full Scale
Repeat Accuracy0.01 %
Supply Voltage90 to 270 V AC
MountingPanel
Operating Temperature0-50 Deg C
Humidity95 % RH

Mechanical:
  • Ambient Temperature And Relative Humidity Surrounding The Controller Must Not Exceed The Maximum Specified Limits.
  • The Controller In Its Installed State Must Be Protected Against Excessive Electrostatic Or Electromagnetic Interferences.

Electrical:
  • The Controller Must Be Wired As Per Wiring Diagram & It Must Comply With Local Electrical Regulation.
  • The Electrical Noise Generated By Switching Inductive Loads Might Create Momentary Fluctuation In Display, Latch Up, Data Loss Or Permanent Damage To The Instrument. To Reduce This Use Snubber Circuit Across The Load.
Request
Callback
Yes! I am Interested

XT-76 Digital Timer

XT-76 Digital Timer
  • XT-76 Digital Timer
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberXT-76
Size72 x 72 mm
BrandI Therm
Display Height0.56 Inch
Reset TimeMore Than 100 ms
Timing Accuracy0.05% Full Scale
Repeat Accuracy0.01 %
Supply Voltage90 to 270 V AC
MountingPanel
Operating Temperature0-50 Deg C
Humidity95 % RH

Mechanical:
  • Ambient Temperature And Relative Humidity Surrounding The Controller Must Not Exceed The Maximum Specified Limits.
  • The Controller In Its Installed State Must Be Protected Against Excessive Electrostatic Or Electromagnetic Interferences.

Electrical:
  • The Controller Must Be Wired As Per Wiring Diagram & It Must Comply With Local Electrical Regulation.
  • The Electrical Noise Generated By Switching Inductive Loads Might Create Momentary Fluctuation In Display, Latch Up, Data Loss Or Permanent Damage To The Instrument. To Reduce This Use Snubber Circuit Across The Load.
Request
Callback
Yes! I am Interested

XT-93 Digital Timer

XT-93 Digital Timer
  • XT-93 Digital Timer
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberXT-93
Size96 x 96 mm
BrandI Therm
Display Height0.56 Inch
Reset TimeMore Than 100 ms
Timing Accuracy0.05% Full Scale
Repeat Accuracy0.01%
Supply Voltage90 to 270 VAC
MountingPanel
Operating Temperature0 ~ 50 Deg C
Humidity95 % RH

Mechanical:
  • Ambient Temperature And Relative Humidity Surrounding The Controller Must Not Exceed The Maximum Specified Limits.
  • The Controller In Its Installed State Must Be Protected Against Excessive Electrostatic Or Electromagnetic Interferences.

Electrical:
  • The Controller Must Be Wired As Per Wiring Diagram & It Must Comply With Local Electrical Regulation.
  • The Electrical Noise Generated By Switching Inductive Loads Might Create Momentary Fluctuation In Display, Latch Up, Data Loss Or Permanent Damage To The Instrument. To Reduce This Use Snubber Circuit Across The Load.
Request
Callback
Yes! I am Interested

XT-96 Digital Timer

XT-96 Digital Timer
  • XT-96 Digital Timer
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberXT-96
Size96 x 96 mm
BrandI Therm
Display Height0.80 Inch
Reset TimeMore Than 100 ms
Timing Accuracy0.05% Full Scale
Repeat Accuracy0.01%
Supply Voltage90 to 270 VAC
MountingPanel
Operating Temperature0 ~ 50 Deg C
Humidity95 % RH

Mechanical:
  • Ambient Temperature And Relative Humidity Surrounding The Controller Must Not Exceed The Maximum Specified Limits.
  • The Controller In Its Installed State Must Be Protected Against Excessive Electrostatic Or Electromagnetic Interferences.

Electrical:
  • The Controller Must Be Wired As Per Wiring Diagram & It Must Comply With Local Electrical Regulation.
  • The Electrical Noise Generated By Switching Inductive Loads Might Create Momentary Fluctuation In Display, Latch Up, Data Loss Or Permanent Damage To The Instrument. To Reduce This Use Snubber Circuit Across The Load.
Request
Callback
Yes! I am Interested

XTM-773 Digital Timer

XTM-773 Digital Timer
  • XTM-773 Digital Timer
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberXTM-773
Size72 x 72 mm
BrandI Therm
Display Height0.56 Inch
Reset TimeMore Than 100 ms
Timing Accuracy0.05% Full Scale
Repeat Accuracy0.01%
Supply Voltage90 to 270 VAC
MountingPanel
Operating Temperature0 ~ 50 Deg C
Humidity95 % RH

Installation Guidelines:
  • Prepare The Cut-out With Proper Dimension As Shown In Figure.
  • Remove Clamp From Timer.
  • Push The Timer Through Panel Cut-out And Secure The Timer In Its Place By Tightening The Side Clamp.

Mechanical:
  • Ambient Temperature And Relative Humidity Surrounding The Controller Must Not Exceed The Maximum Specified Limits.
  • The Controller In Its Installed State Must Be Protected Against Excessive Electrostatic Or Electromagnetic Interferences.

Electrical:
  • The Controller Must Be Wired As Per Wiring Diagram & It Must Comply With Local Electrical Regulation.
  • The Electrical Noise Generated By Switching Inductive Loads Might Create Momentary Fluctuation In Display, Latch Up, Data Loss Or Permanent Damage To The Instrument. To Reduce This Use Snubber Circuit Across The Load.
Request
Callback
Yes! I am Interested

XTM-993 Digital Timer

XTM-993 Digital Timer
  • XTM-993 Digital Timer
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberXTM-993
Size96 x 96 mm
BrandI Therm
Display Height0.56 Inch
Reset TimeMore Than 100 ms
Timing Accuracy0.05% Full Scale
Repeat Accuracy0.01%
Supply Voltage90 to 270 VAC
MountingPanel
Operating Temperature0 ~ 50 Deg C
Humidity95 % RH

Installation Guidelines:
  • Prepare The Cut-out With Proper Dimension As Shown In Figure.
  • Remove Clamp From Timer.
  • Push The Timer Through Panel Cut-out And Secure The Timer In Its Place By Tightening The Side Clamp.

Mechanical:
  • Ambient Temperature And Relative Humidity Surrounding The Controller Must Not Exceed The Maximum Specified Limits.
  • The Controller In Its Installed State Must Be Protected Against Excessive Electrostatic Or Electromagnetic Interferences.

Electrical:
  • The Controller Must Be Wired As Per Wiring Diagram & It Must Comply With Local Electrical Regulation.
  • The Electrical Noise Generated By Switching Inductive Loads Might Create Momentary Fluctuation In Display, Latch Up, Data Loss Or Permanent Damage To The Instrument. To Reduce This Use Snubber Circuit Across The Load.
Request
Callback
Yes! I am Interested

XTM-443 Digital Timer

XTM-443 Digital Timer
  • XTM-443 Digital Timer
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberXTM-443
Size48 x 48 mm
BrandI Therm
Display Height0.39 Inch
Reset TimeMore Than 100 ms
Timing Accuracy0.05% Full Scale
Repeat Accuracy0.01%
Supply Voltage90 to 270 VAC
MountingPanel
Operating Temperature0 ~ 50 Deg C
Humidity95 % RH

Installation Guidelines:
  • Prepare The Cut-out With Proper Dimension As Shown In Figure.
  • Remove Clamp From Timer.
  • Push The Timer Through Panel Cut-out And Secure The Timer In Its Place By Tightening The Side Clamp.

Mechanical:
  • Ambient Temperature And Relative Humidity Surrounding The Controller Must Not Exceed The Maximum Specified Limits.
  • The Controller In Its Installed State Must Be Protected Against Excessive Electrostatic Or Electromagnetic Interferences.

Electrical:
  • The Controller Must Be Wired As Per Wiring Diagram & It Must Comply With Local Electrical Regulation.
  • The Electrical Noise Generated By Switching Inductive Loads Might Create Momentary Fluctuation In Display, Latch Up, Data Loss Or Permanent Damage To The Instrument. To Reduce This Use Snubber Circuit Across The Load.
Request
Callback
Yes! I am Interested

NX 981 Universal Process Controller

NX 981 Universal Process Controller
  • NX 981 Universal Process Controller
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberNX 981
BrandI Therm
Size96*96 mm
Range-1999 to 9999
Display Height0.80 Inch
Resolution0.001 %
Digital Filter1 to 10 Sec
Drive Capacity12 V @ 30 mA
Operating Range0 ~50 Deg C
Storage Humidity95% Rh
Supply Voltage90~270 VAC
Frequency50-60 Hz

Mechanical:
  • Ambient Temperature And Relative Humidity Surrounding The Controller Must Not Exceed The Maximum Specified Limits.
  • The Controller In Its Installed State Must Be Protected Against Excessive Electrostatic Or Electromagnetic Interferences.

Electrical:
  • The Controller Must Be Wired As Per Wiring Diagram & It Must Comply With Local Electrical Regulation.
  • The Electrical Noise Generated By Switching Inductive Loads Might Create Momentary Fluctuation In Display, Latch Up, Data Loss Or Permanent Damage To The Instrument. To Reduce This Use Snubber Circuit Across The Load.
Request
Callback
Yes! I am Interested

NX 982 Universal Process Controller

NX 982 Universal Process Controller
  • NX 982 Universal Process Controller
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberNX 982
BrandI Therm
Size96*96 mm
Sampling Time125 msec
Range-1999 to 9999
Display Height0.80 Inch
Resolution0.001
Digital Filter1 to 10 Sec
Drive Capacity12 V @ 30 mA
Operating Range0 ~50 Deg C
Storage Humidity95% Rh
Supply Voltage90~270 VAC
Frequency50-60 Hz

Mechanical:
  • Ambient Temperature And Relative Humidity Surrounding The Controller Must Not Exceed The Maximum Specified Limits.
  • The Controller In Its Installed State Must Be Protected Against Excessive Electrostatic Or Electromagnetic Interferences.

Electrical:
  • The Controller Must Be Wired As Per Wiring Diagram & It Must Comply With Local Electrical Regulation.
  • The Electrical Noise Generated By Switching Inductive Loads Might Create Momentary Fluctuation In Display, Latch Up, Data Loss Or Permanent Damage To The Instrument. To Reduce This Use Snubber Circuit Across The Load.
Request
Callback
Yes! I am Interested

BL-88 Counters Timer

BL-88 Counters Timer
  • BL-88 Counters Timer
Get Best Quote
Approx. Price: Rs 2,000 / PieceGet Latest Price
Product Brochure

Product Details:

Model Name/NumberBL-88
Accuracy0.05 % Full Scale
Sensor Supply12 V DC (+-10%) @ 30 mA
Humidity95 % RN
BrandI-Them
Supply90 to 270 V AC
Operating Temperature0-55 Deg C

Request
Callback
Yes! I am Interested
X

Explore More Product



Reach Us
Neeraj Ojha (CEO)
Creative Automation System
Kumud Villa, B- 3, Hotel Royal Embassy Road
Basant Vihar, Bhilwara - 311001, Rajasthan, India


Call Us


Send E-mailSend SMS